PIC16C64A-04/P Microchip Technology, PIC16C64A-04/P Datasheet - Page 135

• Manufacturer Part Number: PIC16C64A-04/P
• Description: IC MCU OTP 2KX14 PWM 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C64A-04/P

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Core Processor: PIC
• Speed: 4MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 33
• Ram Memory Size: 128Byte
• Cpu Speed: 4MHz
• No. Of Timers: 3
• No. Of Pwm Channels: 1
• Embedded Interface Type: I2C, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 444-1001 - DEMO BOARD FOR PICMICRO MCU
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: PIC16C64A-04/PR; PIC16C64A-04/PR

FIGURE 13-14: EXTERNAL POWER-ON
Note 1: External Power-on Reset circuit is required
1997 Microchip Technology Inc.
2: R < 40 k is recommended to make sure
3: R1 = 100 to 1 k will limit any current
only if V
diode D helps discharge the capacitor
quickly when V
that voltage drop across R does not violate
the devices electrical specifications.
flowing into MCLR from external capacitor
C in the event of MCLR/V
down due to Electrostatic Discharge
(ESD) or Electrostatic Overstress (EOS).
D
V
DD
RESET CIRCUIT (FOR SLOW
V
DD
R
DD
C
power-up slope is too slow. The
POWER-UP)
DD
R1
powers down.
PIC16CXX
MCLR
PP
pin break-
FIGURE 13-15: EXTERNAL BROWN-OUT
FIGURE 13-16: EXTERNAL BROWN-OUT
Note 1: This brown-out circuit is less expensive,
Note 1: This circuit will activate reset when V
V
V
2: Internal brown-out detection on the
3: Resistors should be adjusted for the
2: Internal brown-out detection on the
3: Resistors should be adjusted for the
DD
DD
albeit less accurate. Transistor Q1 turns
off when V
that:
PIC16C62A/R62/63/R63/64A/R64/65A/
R65/66/67 should be disabled when using
this circuit.
characteristics of the transistors.
goes below (Vz + 0.7V) where Vz = Zener
voltage.
PIC16C62A/R62/63/R63/64A/R64/65A/
R65/66/67 should be disabled when using
this circuit.
characteristics of the transistors.
R1
R2
33k
V
DD
PROTECTION CIRCUIT 1
PROTECTION CIRCUIT 2
•
10k
DD
R1 + R2
is below a certain level such
R1
Q1
PIC16C6X
40k
40k
= 0.7V
MCLR
DS30234D-page 135
V
PIC16CXX
MCLR
V
PIC16CXX
DD
DD
DD