PIC16C64A-04/P Microchip Technology, PIC16C64A-04/P Datasheet - Page 201

• Manufacturer Part Number: PIC16C64A-04/P
• Description: IC MCU OTP 2KX14 PWM 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C64A-04/P

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Core Processor: PIC
• Speed: 4MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 33
• Ram Memory Size: 128Byte
• Cpu Speed: 4MHz
• No. Of Timers: 3
• No. Of Pwm Channels: 1
• Embedded Interface Type: I2C, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 444-1001 - DEMO BOARD FOR PICMICRO MCU
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: PIC16C64A-04/PR; PIC16C64A-04/PR

19.2
DC CHARACTERISTICS
D001
D002*
D003
D004*
D005
D010
D010A
D015*
D020
D021
D021A
D023*
Note 1: This is the limit to which V
Param
1997 Microchip Technology Inc.
*
†
No.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from character-
6: The
These parameters are characterized but not tested.
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and
are not tested.
DC Characteristics:
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all I
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to V
MCLR = V
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
mated by the formula Ir = V
ization and is for design guidance only. This is not tested.
to the base I
age (Note 1)
ensure internal Power-on
Reset signal
internal Power-on Reset
signal
Supply Current (Note 2, 5)
Brown-out Reset Current
(Note 6)
Power-down Current
(Note 3, 5)
Brown-out Reset Current
(Note 6)
Supply Voltage
RAM Data Retention Volt-
V
V
Brown-out Reset Voltage
DD
DD
start voltage to
rise rate to ensure
current is the additional current consumed when this peripheral is enabled. This current should be added
Characteristic
DD
DD
; WDT enabled/disabled as specified.
or I
PD
measurement.
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
DD
DD
PIC16LC62A/R62/64A/R64-04 (Commercial, Industrial)
DD
Standard Operating Conditions (unless otherwise stated)
Operating temperature
can be lowered without losing RAM data.
V
V
V
S
I
I
measurements in active operation mode are:
B
/2Rext (mA) with Rext in kOhm.
DD
PD
Sym
I
I
DD
DR
POR
VDD
VDD
BOR
BOR
0.05
Min
2.5
3.7
-
-
-
-
-
-
-
-
-
Typ† Max Units
22.5
V
350
350
1.5
4.0
2.0
7.5
0.9
0.9
SS
-
-
425
425
6.0
4.3
3.8
48
30
5
5
0˚C
-
-
-
-40˚C
V/ms See section on Power-on Reset for details
mA
V
V
V
V
A
A
A
A
A
A
T
T
XT, RC osc configuration
F
LP osc configuration
F
BOR enabled, V
V
V
V
BOR enabled, V
LP, XT, RC osc configuration (DC - 4 MHz)
See section on Power-on Reset for details
BODEN bit in configuration word enabled
A
A
OSC
OSC
DD
DD
DD
+85˚C for industrial and
+70˚C for commercial
= 3.0V, WDT enabled, -40 C to +85 C
= 3.0V, WDT disabled, 0 C to +70 C
= 3.0V, WDT disabled, -40 C to +85 C
= 4 MHz, V
= 32 kHz, V
DD
PIC16C6X
DD
DD
Conditions
DD
DD
= 5.0V
= 5.0V
= 3.0V (Note 4)
= 3.0V, WDT disabled
DD
DS30234D-page 201
and V
SS
.