PIC18F2221-I/ML Microchip Technology, PIC18F2221-I/ML Datasheet - Page 164

• Manufacturer Part Number: PIC18F2221-I/ML
• Description: IC PIC MCU FLASH 2KX16 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2221-I/ML

• Core Size: 8-Bit
• Program Memory Size: 4KB (2K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 28QFN EP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 25
• Interface Type: I2C/SPI/USART
• On-chip Adc: 10-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28QFN4 - SOCKET TRANS ICE 28QFN W/CABLEAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

registers in SPI mode operation. The SSPCON1 register
SSPSTAT are read-only. The upper two bits of the
SSPSTAT are read/write.
PIC18F4321 FAMILY
17.3.1
The MSSP module has four registers for SPI mode
operation. These are:
• MSSP Control Register 1 (SSPCON1)
• MSSP Status Register (SSPSTAT)
• Serial Receive/Transmit Buffer Register
• MSSP Shift Register (SSPSR) – Not directly
SSPCON1 and SSPSTAT are the control and status
is readable and writable. The lower 6 bits of the
REGISTER 17-1:
DS39689E-page 162
(SSPBUF)
accessible
REGISTERS
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
SSPSTAT: MSSP STATUS REGISTER (SPI MODE)
bit 7
SMP: Sample bit
SPI Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time
SPI Slave mode:
SMP must be cleared when SPI is used in Slave mode.
CKE: SPI Clock Select bit
1 = Transmit occurs on transition from active to Idle clock state
0 = Transmit occurs on transition from Idle to active clock state
D/A: Data/Address bit
Used in I
P: Stop bit
Used in I
cleared.
S: Start bit
Used in I
R/W: Read/Write Information bit
Used in I
UA: Update Address bit
Used in I
BF: Buffer Full Status bit (Receive mode only)
1 = Receive complete, SSPBUF is full
0 = Receive not complete, SSPBUF is empty
Legend:
R = Readable bit
-n = Value at POR
R/W-0
Note:
SMP
2
2
2
2
2
C™ mode only.
C mode only. This bit is cleared when the MSSP module is disabled, SSPEN is
C mode only.
C mode only.
C mode only.
Polarity of clock state is set by the CKP bit (SSPCON1<4>).
R/W-0
CKE
W = Writable bit
‘1’ = Bit is set
Preliminary
R-0
D/A
R-0
SSPSR is the shift register used for shifting data in or
out. SSPBUF is the buffer register to which data bytes
are written to or read from.
In receive operations, SSPSR and SSPBUF together
create a double-buffered receiver. When SSPSR
receives a complete byte, it is transferred to SSPBUF
and the SSPIF interrupt is set.
During transmission, the SSPBUF is not double-
buffered. A write to SSPBUF will write to both SSPBUF
and SSPSR.
P
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R-0
S
R/W
R-0
© 2007 Microchip Technology Inc.
x = Bit is unknown
R-0
UA
R-0
BF
bit 0