PIC18F2221-I/ML Microchip Technology, PIC18F2221-I/ML Datasheet - Page 380

• Manufacturer Part Number: PIC18F2221-I/ML
• Description: IC PIC MCU FLASH 2KX16 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2221-I/ML

• Core Size: 8-Bit
• Program Memory Size: 4KB (2K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 28QFN EP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 25
• Interface Type: I2C/SPI/USART
• On-chip Adc: 10-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28QFN4 - SOCKET TRANS ICE 28QFN W/CABLEAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F4321 FAMILY
APPENDIX C:
This appendix discusses the considerations for
converting from previous versions of a device to the
ones listed in this data sheet. Typically, these changes
are due to the differences in the process technology
used. An example of this type of conversion is from a
PIC16C74A to a PIC16C74B.
The PIC18F4321 family of devices is functionally the
same as the PIC18F4320 family. Code written for a
PIC18F4320 will generally work on a PIC18F4321 with
few or no changes.
The following is a list of changes the user should be
aware of when migrating an application from the
PIC18F4320 to the PIC18F4321. Code written for the
PIC18F4321 may not run as expected due to these
differences.
1.
2.
3.
4.
DS39689E-page 378
Entry to power-managed modes has changed.
Modifying the SCS1:SCS0 bits (OSCCON<1:0>)
immediately changes the current clock source. It
is not necessary to execute a SLEEP instruction
to change clock sources. Refer to Section 3.1.2
“Entering Power-Managed Modes” for details.
Exit from power-managed modes has changed.
A WDT wake or interrupt does not cause an
automatic return to PRI_RUN mode. The
controller will execute code while continuing to
use the current clock source. If the controller
was operating in RC_IDLE or RC_RUN mode,
an interrupt will cause entry to RC_RUN mode
until code selects another power-managed
mode. Refer to Section 3.4 “Idle Modes” for
details.
The extended instruction set can be con-
(CONFIG4L<6>). The access memory map is
also modified when the extended instruction set
is enabled. Refer to Section 5.5 “Data Memory
and the Extended Instruction Set” and
Section 24.2 “Extended Instruction Set” for
details.
There may also be changes to the electrical spec-
ifications. Refer to Section 26.0 “Electrical
Characteristics” for details.
figured as enabled using the XINST bit
CONVERSION
CONSIDERATIONS
Preliminary
APPENDIX D:
This section discusses how to migrate from a Baseline
device (i.e., PIC16C5X) to an Enhanced MCU device
(i.e., PIC18FXXX).
The following are the list of modifications over the
PIC16C5X microcontroller family:
Not Currently Available
MIGRATION FROM
BASELINE TO
ENHANCED DEVICES
© 2007 Microchip Technology Inc.