AT91SAM7SE512-AU Atmel, AT91SAM7SE512-AU Datasheet - Page 250

• Manufacturer Part Number: AT91SAM7SE512-AU
• Description: IC ARM7 MCU FLASH 512K 128-LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7SE512-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: EBI/EMI, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 88
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 128-LQFP
• Cpu Family: 91S
• Device Core: ARM7TDMI
• Device Core Size: 32b
• Frequency (max): 55MHz
• Interface Type: EBI/SPI/TWI/USART
• Total Internal Ram Size: 32KB
• # I/os (max): 88
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 128
• Package Type: LQFP
• No. Of I/o's: 88
• Ram Memory Size: 32KB
• Cpu Speed: 48MHz
• No. Of Timers: 3
• No. Of Pwm Channels: 4
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7S-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7SE-EK
• Minimum Operating Temperature: - 40 C
• For Use With: AT91SAM7SE-EK - EVAL BOARD FOR AT91SAM7SEAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

27.7.2
27.7.2.1
250
SAM7SE512/256/32 Preliminary
Interrupt Latencies
External Interrupt Edge Triggered Source
Global interrupt latencies depend on several parameters, including:
This section addresses only the hardware resynchronizations. It gives details of the latency
times between the event on an external interrupt leading in a valid interrupt (edge or level) or the
assertion of an internal interrupt source and the assertion of the nIRQ or nFIQ line on the pro-
cessor. The resynchronization time depends on the programming of the interrupt source and on
its type (internal or external). For the standard interrupt, resynchronization times are given
assuming there is no higher priority in progress.
The PIO Controller multiplexing has no effect on the interrupt latencies of the external interrupt
sources.
Figure 27-6.
• The time the software masks the interrupts.
• Occurrence, either at the processor level or at the AIC level.
• The execution time of the instruction in progress when the interrupt occurs.
• The treatment of higher priority interrupts and the resynchronization of the hardware signals.
External Interrupt Edge Triggered Source
(Negative Edge)
(Positive Edge)
IRQ or FIQ
IRQ or FIQ
nIRQ
MCK
nFIQ
Maximum IRQ Latency = 4 Cycles
Maximum FIQ Latency = 4 Cycles
6222F–ATARM–14-Jan-11