AT91SAM7SE512-AU Atmel, AT91SAM7SE512-AU Datasheet - Page 364

• Manufacturer Part Number: AT91SAM7SE512-AU
• Description: IC ARM7 MCU FLASH 512K 128-LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7SE512-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: EBI/EMI, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 88
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 128-LQFP
• Cpu Family: 91S
• Device Core: ARM7TDMI
• Device Core Size: 32b
• Frequency (max): 55MHz
• Interface Type: EBI/SPI/TWI/USART
• Total Internal Ram Size: 32KB
• # I/os (max): 88
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 128
• Package Type: LQFP
• No. Of I/o's: 88
• Ram Memory Size: 32KB
• Cpu Speed: 48MHz
• No. Of Timers: 3
• No. Of Pwm Channels: 4
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7S-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7SE-EK
• Minimum Operating Temperature: - 40 C
• For Use With: AT91SAM7SE-EK - EVAL BOARD FOR AT91SAM7SEAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

32.8
32.8.1
32.8.2
32.8.2.1
32.8.2.2
364
Multi-master Mode
SAM7SE512/256/32 Preliminary
Definition
Different Multi-master Modes
TWI as Master Only
TWI as Master or Slave
More than one master may handle the bus at the same time without data corruption by using
arbitration.
Arbitration starts as soon as two or more masters place information on the bus at the same time,
and stops (arbitration is lost) for the master that intends to send a logical one while the other
master sends a logical zero.
As soon as arbitration is lost by a master, it stops sending data and listens to the bus in order to
detect a stop. When the stop is detected, the master who has lost arbitration may put its data on
the bus by respecting arbitration.
Arbitration is illustrated in
Two multi-master modes may be distinguished:
Note:
In this mode, TWI is considered as a Master only (MSEN is always at one) and must be driven
like a Master with the ARBLST (ARBitration Lost) flag in addition.
If arbitration is lost (ARBLST = 1), the programmer must reinitiate the data transfer.
If the user starts a transfer (ex.: DADR + START + W + Write in THR) and if the bus is busy, the
TWI automatically waits for a STOP condition on the bus to initiate the transfer (see
20 on page
Note:
The automatic reversal from Master to Slave is not supported in case of a lost arbitration.
Then, in the case where TWI may be either a Master or a Slave, the programmer must manage
the pseudo Multi-master mode described in the steps below.
1. TWI is considered as a Master only and will never be addressed.
2. TWI may be either a Master or a Slave and may be addressed.
1. Program TWI in Slave mode (SADR + MSDIS + SVEN) and perform Slave Access (if
2. If TWI has to be set in Master mode, wait until TXCOMP flag is at 1.
3. Program Master mode (DADR + SVDIS + MSEN) and start the transfer (ex: START +
4. As soon as the Master mode is enabled, TWI scans the bus in order to detect if it is
5. As soon as the transfer is initiated and until a STOP condition is sent, the arbitration
6. If the arbitration is lost (ARBLST is set to 1), the user must program the TWI in Slave
7. If TWI has to be set in Slave mode, wait until TXCOMP flag is at 1 and then program the
TWI is addressed).
Write in THR).
busy or free. When the bus is considered as free, TWI initiates the transfer.
becomes relevant and the user must monitor the ARBLST flag.
mode in the case where the Master that won the arbitration wanted to access the TWI.
Slave mode.
In both Multi-master modes arbitration is supported.
The state of the bus (busy or free) is not indicated in the user interface.
365).
Figure 32-21 on page
365.
6222F–ATARM–14-Jan-11
Figure 32-