LAN8187-JT SMSC, LAN8187-JT Datasheet - Page 28

• Manufacturer Part Number: LAN8187-JT
• Description: Ethernet ICs HiPerfrm Ethrnt PHY
• Manufacturer: SMSC
• Type: MII/RMII Ethernet Transceiverr

Specifications of LAN8187-JT

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Transceivers
• Number Of Transceivers: 1
• Standard Supported: 802.3ab
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 1.8 V
• Supply Current (max): 39 mA, 81.6 mA
• Maximum Operating Temperature: + 70 C
• Package / Case: TQFP-64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Revision 1.7 (03-04-11)
The following blocks are activated during an Auto-negotiation session:
When enabled, auto-negotiation is started by the occurrence of one of the following events:
On detection of one of these events, the PHY begins auto-negotiation by transmitting bursts of Fast
Link Pulses (FLP). These are bursts of link pulses from the 10M transmitter. They are shaped as
Normal Link Pulses and can pass uncorrupted down CAT-3 or CAT-5 cable. A Fast Link Pulse Burst
consists of up to 33 pulses. The 17 odd-numbered pulses, which are always present, frame the FLP
burst. The 16 even-numbered pulses, which may be present or absent, contain the data word being
transmitted. Presence of a data pulse represents a “1”, while absence represents a “0”.
The data transmitted by an FLP burst is known as a “Link Code Word.” These are defined fully in IEEE
802.3 clause 28. In summary, the PHY advertises 802.3 compliance in its selector field (the first 5 bits
of the Link Code Word). It advertises its technology ability according to the bits set in register 4 of the
SMI registers.
There are 4 possible matches of the technology abilities. In the order of priority these are:
If the full capabilities of the PHY are advertised (100M, Full Duplex), and if the link partner is capable
of 10M and 100M, then auto-negotiation selects 100M as the highest performance mode. If the link
partner is capable of Half and Full duplex modes, then auto-negotiation selects Full Duplex as the
highest performance operation.
Once a capability match has been determined, the link code words are repeated with the acknowledge
bit set. Any difference in the main content of the link code words at this time will cause auto-negotiation
to re-start. Auto-negotiation will also re-start if not all of the required FLP bursts are received.
The capabilities advertised during auto-negotiation by the PHY are initially determined by the logic
levels latched on the MODE[2:0] bus after reset completes. This bus can also be used to disable auto-
negotiation on power-up.
Writing register 4 bits [8:5] allows software control of the capabilities advertised by the PHY. Writing
register 4 does not automatically re-start auto-negotiation. Register 0, bit 9 must be set before the new
abilities will be advertised. Auto-negotiation can also be disabled via software by clearing register 0,
bit 12.
The LAN8187/LAN8187i does not support “Next Page” capability.
Auto-negotiation (digital)
100M ADC (analog)
100M PLL (analog)
100M equalizer/BLW/clock recovery (DSP)
10M SQUELCH (analog)
10M PLL (analog)
10M Transmitter (analog)
Hardware reset
Software reset
Power-down reset
Link status down
Setting register 0, bit 9 high (auto-negotiation restart)
100M Full Duplex (Highest priority)
100M Half Duplex
10M Full Duplex
10M Half Duplex
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX & flexPWR
DATASHEET
28
SMSC LAN8187/LAN8187i
Datasheet
®
Technology