ISL29004IROZ Intersil, ISL29004IROZ Datasheet - Page 7

• Manufacturer Part Number: ISL29004IROZ
• Description: IC SENSOR LIGHT-DGTL I2C 8-ODFN
• Manufacturer: Intersil
• Series: -r

Specifications of ISL29004IROZ

• Wavelength: 550nm
• Output Type: I²C™
• Package / Case: 8-WFDFN Exposed Pad
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

d
Command Register 00(hex)
The Read/Write command register has five functions:
(1) Enable; Bit 7.This function either resets the ADC or
enables the ADC in normal operation. A logic 0 disables
ADC to reset-mode. A logic 1 enables adc to normal
operation.
(2) AdcPD; Bit 6. This function puts the device in a power
down mode. A logic 0 puts the device in normal operation. A
logic 1 powers down the device.
(3) Timing Mode; Bit 5. This function determines whether the
integration time is done internally or externally. In Internal
Timing Mode, integration time is determined by an internal
dual speed oscillator (fosc), and the n-bit (n = 4, 8, 12,16)
counter inside the ADC. In External Timing Mode, integration
time is determined by the time between two consecutive
external-sync sync_iic pules commands.
(4) Photodiode Select Mode; Bits 3 and 2. This function
controls the mux attached to the two photodiodes. At Mode0,
the mux directs the current of Diode1 to the ADC. At Mode1,
the mux directs the current of Diode2 only to the ADC.
b1xxx_xxxx
bx1xx_xxxx
ADDRESS
BIT 7
BIT 6
BIT 5
0
1
0
1
0
1
Disable ADC-core to reset-mode (default)
Enable ADC-core to normal operation
Normal operation (default)
Power Down
Internal Timing Mode. Integration time is internally
timed determined by fosc, REXT, and number of clock
cycles.
External Timing Mode. Integration time is externally
timed by the I2C host.
REGISTER
TABLE 2. WRITE ONLY REGISTERS
sync_iic
clar_int
NAME
TABLE 5. TIMING MODE
TABLE 3. ENABLE
TABLE 4. adcPD
Writing a logic 1 to this address bit ends
the current adc-integration and starts
another. Used only with External Timing
Mode.
Writing a logic 1 to this address bit
clears the interrupt.
7
OPERATION
OPERATION
OPERATION
DESCRIPTION
FUNCTIONS/
ISL29004
Mode3 is a sequential Mode0 and Mode1 with an internal
subtract function (Diode1 - Diode2).
* n = 4, 8, 12,16 depending on the number of clock cycles
function.
(5) Width; Bits 1 and 0. This function determines the number
of clock cycles per conversion. Changing the number of
clock cycles does more than just change the resolution of
the device. It also changes the integration time, which is the
period the device’s analog-to-digital (A/D) converter samples
the photodiode current signal for a Lux measurement.
Control Register 01(hex)
The Read/Write control register has three functions:
(1) Interrupt flag; Bit 5. This is the status bit of the interrupt.
The bit is set to logic high when the interrupt thresholds have
been triggered, and logic low when not yet triggered. Writing
a logic low clears/resets the status bit.
(2) Range/Gain; Bits 3 and 2. The Full Scale Range can be
adjusted by an external resistor Rext and/or it can be
adjusted via I2C using the Gain/Range funtion. Gain/Range
has four possible values, Range(k) where k is 1 through 4.
Table 9 lists the possible values of Range(k) and the
resulting FSR for some typical value R
Gain/Range is set to Range1 or Range2, the fosc runs at
327kHz. When Gain/Range is set to Range3 or Range4 fosc
runs at twice the rate at 655kHz. The automatic fosc
adjustment feature improves signal-to-noise ratio for low Lux
measurements.
BITS 3:2
BITS 1:0
0:0
0:1
1:0
1:1
BIT 5
TABLE 6. PHOTODIODE SELECT MODE; BITS 2 AND 3
0:0
0:1
1:0
1:1
0
1
Mode0. ADC integrates or converts Diode1 only. Current
is converted to an n-bit unsigned data.*
Mode1. ADC integrates or coverts Diode2 only. Current is
converted to an n-bit unsigned data.*
MODE3. A sequential Mode0 then Mode1 operation. The
difference current is an (n-1) signed data.*
No operation.
2^16 = 65,536
2^12 = 4,096
2^8 = 256
2^4 = 16
Interrupt is cleared or not triggered yet
Interrupt is triggered
TABLE 8. INTERRUPT FLAG
NUMBER OF CLOCK CYCLES
TABLE 7. WIDTH
OPERATION
MODE
EXT
resistors. When
December 21, 2006
FN6221.0