KS8999 Micrel Inc, KS8999 Datasheet - Page 14

• Manufacturer Part Number: KS8999
• Description: IC SWITCH 10/100 9PORT 208PQFP
• Manufacturer: Micrel Inc

Specifications of KS8999

• Applications: *
• Mounting Type: Surface Mount
• Package / Case: 208-MQFP, 208-PQFP
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Phy/transceiver Interface: MII/SNI
• Power Supply Type: Analog/Digital
• Package Type: PQFP
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Mounting: Surface Mount
• Jtag Support: No
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: 576-1023 - BOARD EVAL EXPERIMENT FOR KS8999
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant

KS8999
Note 1.
KS8999
Group
UP
All unmanaged programming takes place at reset time only. For unmanaged programming: F = Float, D = Pull-down, U = Pull-up.
See
“Reference Circuits”
MODESEL[3:0]
LED[1:9][1]
LED[1:9][2]
LED[1:9][3]
I/O Names
LED[1][3]
LED[1][2]
LED[1][1]
Active Status
section.
H
L
L
L
Description
Output (after reset)
Mode 0: Full Duplex (on = full/off = half)
Mode 1: Full Duplex (on = full/off = half)
Mode 2: Full Duplex (on = full/off = half)
Mode 3: Reserved
Output (after reset)
Mode 0: Collision (on = collision/off = no collision)
Mode 1: Transmit Activity (on during transmission)
Mode 2: Link activity (10Mb mode)
Mode 3: Full Duplex + Collision
(constant on = full duplex; intermittent on = collision; off = half-duplex with no collision)
Output (after reset)
Mode 0: Link + Activity
When LED is solid “on”, it indicates the link is on for both 10 or 100BaseTX, but no
data is transmitting or receiving.
When LED is solid “off”, it indicates the link is off.
When LED is blinking, it indicates data is transmitting or receiving for either 10 or 100
BaseTX
Mode 1: Receive Activity (on = receiving/off = not receiving)
Mode 2: Link activity (100Mb mode)
Mode 3: Link + Activity (see description above)
Note: Mode is set by MODESEL[3:0] ; please see description in UP (unmanaged
programming) section.
Mode select at reset time. LED mode is selected by using the table below. Note that
under normal operation MODESEL[3:2] must be tied low.
MODESEL
3 2 1 0
0 0 0 0
0 0 0 1
0 0 1 0
0 0 1 1
0 1 0 0
0 1 0 1
0 1 1 0
0 1 1 1
1 0 0 0
1 0 0 1
1 0 1 0
1 0 1 1
1 1 0 0
1 1 0 1
1 1 1 0
1 1 1 1
Programs auto-negotiation on port 1
D = Disable auto-negotiation, F/U = Enable auto-negotiation (default)
Programs auto-negotiation on port 2
D = Disable auto-negotiation, F/U = Enable auto-negotiation (default)
Programs auto-negotiation on port 3
D = Disable auto-negotiation, F/U = Enable auto-negotiation (default)
(Note 1)
Operation
LED mode 0
LED mode 1
LED mode 2
LED mode 3
Used for factory testing
Used for factory testing
Used for factory testing
Used for factory testing
Used for factory testing
Used for factory testing
Used for factory testing
Used for factory testing
Used for factory testing
Used for factory testing
Used for factory testing
Used for factory testing
14
January 2005
Micrel