ST7MDT10-TEB/DVP STMicroelectronics, ST7MDT10-TEB/DVP Datasheet
ST7MDT10-TEB/DVP
Specifications of ST7MDT10-TEB/DVP
Related parts for ST7MDT10-TEB/DVP
ST7MDT10-TEB/DVP Summary of contents
Page 1
... ST7MDT10-DVP3 Ref: DOC-ST7MDT10-DVP3 Probe User Guide Release 2.0 March 2005 ...
Page 2
... Requirements on page 26 for relevant safety information. USE IN LIFE SUPPORT DEVICES OR SYSTEMS MUST BE EXPRESSLY AUTHORIZED. STMicroelectronics PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF STMicroelectronics. As used herein: 1. Life support devices or systems are those ...
Page 3
Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
... The ST7MDT10-DVP3 probe, consisting of the Target Emulation Board (TEB), Adapter Kit and flat cables ( emulate MCUs from different families, with different packages. The Target Emulation Board contains target-emulating hardware that is specific to an ST7 MCU family of MCUs. Your ST7MDT10-TEB/DVP emulates MCUs in the ST7LITE(S/0/1/2), ST7FDALI and ST7226(0/2/4) families. ST7MDT10-DVP3 Probe ...
Page 5
... ST7-DVP3 Emulator User Manual - set up instructions for your DVP3 emulator ST7xxxx Datasheet - includes debugging and programming information that is specific to your MCU Because of the modularity of the DVP3 emulator, this guide is delivered with the following kits: • ST7MDT10-TEB/DVP • ST7MDT10-DVP3 emulator DIP16, SO16, DIP20, SO20, DIP32, SO28. ): Introduction ...
Page 6
... If you already own an ST7-DVP3 emulator, your emulator’s MEB can be adapted to emulate devices in the ST7LITE(S/0/1/2), ST7FDALI and ST7226(0/2/4) families with the appropriate target emulation board (ordering code: ST7MDT10-TEB/DVP) and the adapters and sockets that correspond to your microcontroller’s package. Ordering code ...
Page 7
... DVP Table 1: Ordering codes and associated components 1) This adapter kit is provided by default with the ST7MDT10-DVP3 and ST7MDT10-TEB/DVP if you did not specify another adapter kit (ST7MDT10-20/DVP, ST7MDT10-32/DVP) when you ordered your emula- tor. 2) This flat cable is provided in addition to the 34-pin flat cable that is provided by default with all ST7MDT10-DVP3 emulators and target emulation boards ...
Page 8
... Delivery checklist (e) 8/31 (a) (b) (d) (f) (i) Figure 2: ST7MDT10-DVP3 components ST7MDT10-DVP3 Probe User Guide (c) (g) (h) ...
Page 9
... ST7MDT10-DVP3 Probe User Guide 3 CONNECTING TO YOUR APPLICATION BOARD In addition to providing the firmware to emulate your MCU, the ST7MDT10-DVP3 emulator serves as the hardware interface between your host PC and your application. Your DVP3 emulator comes with the connectors and adapters for a specific package type. These accessories allow you to connect your emulator to your application board in place of your ST7 microcontroller ...
Page 10
... Solder the DIP16 socket to your application board. 2 Ensure that the emulator and your application board are powered off. 3 Connect the 34-pin flat cable to the J1 connector on the ST7MDT10-DVP3 TEB, making certain to align the orientation guides as shown in J2 connector on your TEB is not used in this configuration. ...
Page 11
... ST7MDT10-DVP3 Probe User Guide 6 Insert the pins of the device adapter’s DIP16 adapter into the socket that is soldered on your application board (see indicators on the device adapter and on your application board to ensure that the socket’s pin number 1 is aligned with pin 1 on the device adapter. ...
Page 12
... Ensure that the emulator and your application board are powered off. 3 Connect the 34-pin flat cable to the J1 connector on the ST7MDT10-DVP3 TEB, making certain to align the orientation guides as shown in J2 connector on your TEB is not used in this configuration. ...
Page 13
... ST7MDT10-DVP3 Probe User Guide 6 Insert the pins of the SO16 connector that is soldered on your application board, into the DIP16/SO16 device adapter, as shown in indicators on the device adapter and on your application board to ensure that pin 1 is aligned with pin 1 on the adapter. Refer to your ST7-DVP3 Emulator User Manual for information about connecting your emulator to your PC ...
Page 14
... Solder the DIP20 socket to your application board. 2 Ensure that the emulator and your application board are powered off. 3 Connect the 34-pin flat cable to the J1 connector on the ST7MDT10-DVP3 TEB, making certain to align the orientation guides as shown in J2 connector on your TEB is not used in this configuration. ...
Page 15
... ST7MDT10-DVP3 Probe User Guide 5 Insert the pins of the DIP20 adapter into the DIP20-DIP20 device adapter (ref.: DB535), as shown in 6 Insert the device adapter’s pins into the socket soldered on your application board, as shown in pin number 1 of the adapter, device adapter and socket are all aligned. ...
Page 16
... Ensure that the emulator and your application board are powered off. 3 Connect the 34-pin flat cable to the J1 connector on the ST7MDT10-DVP3 TEB, making certain to align the orientation guides as shown in J2 connector on your TEB is not used in this configuration. ...
Page 17
... ST7MDT10-DVP3 Probe User Guide 5 Insert the pins of the DIP20 adapter into the SO20 device adapter (ref.: DB093) as shown in on your application board to ensure that its pin number 1 is aligned with pin 1 on your application board. Refer to your ST7-DVP3 Emulator User Manual for information about connecting your emulator to your PC ...
Page 18
... Solder the SDIP32 socket to your application board. 2 Ensure that the emulator and your application board are powered off. 3 Connect the 34-pin flat cable to the J1 connector on the ST7MDT10-DVP3 TEB, making certain to align the orientation guides as shown in connect the 26-pin flat cable to the J2 connector, in the same manner. ...
Page 19
... Ensure that the emulator and your application board are powered off. 3 Connect the 34-pin flat cable to the J1 connector on the ST7MDT10-DVP3 TEB, making certain to align the orientation guides as shown in connect the 26-pin flat cable to the J2 connector, in the same manner. ...
Page 20
... Align the orientation indicators on the SDIP32 adapter and on your application board to ensure that the its pin number 1 is aligned with pin 1 on your application board. Refer to your ST7-DVP3 Emulator User Manual for information about connecting your emulator to your PC. 20/31 ST7MDT10-DVP3 Probe User Guide ...
Page 21
... ST7MDT10-DVP3 Probe User Guide 3.7 Installing HE10 connectors on your application board This section provides information about installing HE10 connectors directly on your application board to receive the emulator’s flat cables. Doing this allows you to connect your emulator directly to the application board without using the connectors/sockets and adapters described in previous sections ...
Page 22
... I/O port B bit 5 I/O port B bit 6 I/O port A bit 0 I/O port A bit 1 I/O port A bit 2 I/O port A bit 3 I/O port C bit 0 I/O port C bit 1 Table 2: Pin correspondence for J1 connector ST7MDT10-DVP3 Probe User Guide Description/ Pin No. Name Comments 2 VDD MCU VDD 4 GND ...
Page 23
... ST7MDT10-DVP3 Probe User Guide Pin No. Name 1 Reserved, this pin must not be 3 GND 5 GND 7 GND 9 Reserved, this pin must not be 11 GND 13 GND 15 GND 17 GND 19 GND 21 GND 23 Reserved, this pin must not be 25 GND Caution: When installing the J2 connector, pins that are indicated as Reserved in be connected ...
Page 24
... You can configure certain on-chip peripherals in ST7 Visual Develop’s MCU Configuration dialog box so that the emulator accurately emulates your target device. The on-chip peripheral options available for configuration for the ST7MDT10-DVP3 emulator are described in this section. MCU The MCU Selection tab in STVD7’s Project Settings window allows you to select from a list of MCU’ ...
Page 25
... ST7MDT10-DVP3 Probe User Guide 4.2 Emulation functional limitations and discrepancies 4.2.1 Power supply limitation Power supply configuration of the ST7-DVP3 can be set to either 3 using the SW1 switch located on the ST7-DVP3 MEB (ref.: DB352). Voltage for all ports is either 3 CMOS compatible depending of the SW1 position chosen. ...
Page 26
... If you are using this product under conditions where there may be blackouts or power surges (such as during an electrical storm recommended that you isolate it by elevating it at least 10 cm above the grounded work surface using blocks of insulating material. 26/31 ST7MDT10-DVP3 Probe User Guide 2 ), grounded through a ground cable (conductive cable ...
Page 27
... ST7MDT10-DVP3 Probe User Guide APPENDIX B: REVISION HISTORY Date Dec 2004 Mar 2005 Table 5: ST7MDT10-DVP3 Probe User Guide revision history Revision 1.1 • Replaced “ST7 Visual Debug” with “ST7 Visual Develop” • Replaced “passive probe” with “adapter” • Added ...
Page 28
... Complete documentation and ordering information for P/TQFP sockets from Yamaichi, Ironwood, CAB and Enplas are provided at the following Internet sites: www.yamaichi.de www.ironwoodelectronics.com www.cabgmbh.com www.enplas.com Connectors Complete documentation and ordering information for SAMTEC connectors is provided at www.samtec.com. 28/31 ST7MDT10-DVP3 Probe User Guide Contact List provided ...
Page 29
... ST7MDT10-DVP3 Probe User Guide Getting prepared before you call Collect the following information about the product before contacting ST or your distributor: 1 Name of the company where you purchased the product. 2 Date of purchase. 3 Order Code: Refer to the side your emulators box. The order code will depend on the region in which is was ordered (i ...
Page 30
... Germany + U.K. +44 162 889 0800 Japan +81 3 3280 4120 Hong-Kong +85 2 2861 5700 Sydney +61 2 9580 3811 Taipei + 2378 8088 30/31 ST7MDT10-DVP3 Probe User Guide North America Mid West STMicroelectronics 1300 East Woodfield Road, Suite 410 Schaumburg, IL 60173 Phone: (847) 585-3000 ...
Page 31
... No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. ...