PIC12F675-I/P Microchip Technology, PIC12F675-I/P Datasheet - Page 33
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC12F675-I/P
Manufacturer Part Number
PIC12F675-I/P
Description
IC MCU CMOS FLASH-BASE 8BIT 8DIP
Manufacturer
Microchip Technology
Series
PIC® 12Fr
Datasheets
1.PIC12F629T-ISN.pdf
(136 pages)
2.PIC12F629T-ISN.pdf
(8 pages)
3.PIC12F629T-ISN.pdf
(24 pages)
4.PIC12F675-ESN.pdf
(132 pages)
Specifications of PIC12F675-I/P
Program Memory Type
FLASH
Program Memory Size
1.75KB (1K x 14)
Package / Case
8-DIP (0.300", 7.62mm)
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Peripherals
POR, WDT
Number Of I /o
5
Eeprom Size
128 x 8
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC12F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
64 B
Interface Type
RS- 232/USB
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
6
Number Of Timers
2
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 53270-913
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
Minimum Operating Temperature
- 40 C
On-chip Adc
4-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DM163029 - BOARD PICDEM FOR MECHATRONICSAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
Connectivity
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC12F675-I/P
Manufacturer:
MICROCHIP
Quantity:
5 000
Company:
Part Number:
PIC12F675-I/P
Manufacturer:
MCP
Quantity:
12 420
Part Number:
PIC12F675-I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
5.1
Timer1 can operate in one of three modes:
• 16-bit timer with prescaler
• 16-bit synchronous counter
• 16-bit asynchronous counter
In Timer mode, Timer1 is incremented on every
instruction cycle. In Counter mode, Timer1 is
incremented on the rising edge of the external clock
input T1CKI. In addition, the Counter mode clock can
be synchronized to the microcontroller system clock
or run asynchronously.
In counter and timer modules, the counter/timer clock
can be gated by the T1G input.
If an external clock oscillator is needed (and the
microcontroller is using the INTOSC w/o CLKOUT),
Timer1 can use the LP oscillator as a clock source.
FIGURE 5-2:
2010 Microchip Technology Inc.
Note:
T1CKI =
when TMR1
Enabled
T1CKI =
when TMR1
Enabled
Note 1: Arrows indicate counter increments.
Timer1 Modes of Operation
2: In Counter mode, a falling edge must be registered by the counter prior to the first incrementing rising edge of the
In Counter mode, a falling edge must be
registered by the counter prior to the first
incrementing rising edge.
1
0
clock.
TIMER1 INCREMENTING EDGE
5.2
The Timer1 register pair (TMR1H:TMR1L) increments
to FFFFh and rolls over to 0000h. When Timer1 rolls
over, the Timer1 interrupt flag bit (PIR1<0>) is set. To
enable the interrupt on rollover, you must set these bits:
• Timer1 interrupt Enable bit (PIE1<0>)
• PEIE bit (INTCON<6>)
• GIE bit (INTCON<7>).
The interrupt is cleared by clearing the TMR1IF in the
Interrupt Service Routine.
5.3
Timer1 has four prescaler options allowing 1, 2, 4, or 8
divisions of the clock input. The T1CKPS bits
(T1CON<5:4>) control the prescale counter. The
prescale counter is not directly readable or writable;
however, the prescaler counter is cleared upon a write
to TMR1H or TMR1L.
Note:
Timer1 Interrupt
Timer1 Prescaler
The TMR1H:TTMR1L register pair and the
TMR1IF bit should be cleared before
enabling interrupts.
PIC12F629/675
DS41190G-page 33