PIC16F1938-I/ML Microchip Technology, PIC16F1938-I/ML Datasheet - Page 105

• Manufacturer Part Number: PIC16F1938-I/ML
• Description: IC MCU 8BIT FLASH 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1938-I/ML

• Core Size: 8-Bit
• Program Memory Size: 28KB (16K x 14)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC16F
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1024Byte
• Cpu Speed: 32MHz
• Package: 28QFN EP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 32 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 25
• Interface Type: I2C/SPI/USART
• On-chip Adc: 11-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

7.0
The PORTB pins can be configured to operate as
Interrupt-On-Change (IOC) pins. An interrupt can be
generated by detecting a signal that has either a rising
edge or a falling edge. Any individual PORTB pin, or
combination of PORTB pins, can be configured to
generate an interrupt. The interrupt-on-change module
has the following features:
• Interrupt-on-Change enable (Master Switch)
• Individual pin configuration
• Rising and falling edge detection
• Individual pin interrupt flags
Figure 7-1 is a block diagram of the IOC module.
7.1
To allow individual PORTB pins to generate an interrupt,
the IOCIE bit of the INTCON register must be set. If the
IOCIE bit is disabled, the edge detection on the pin will
still occur, but an interrupt will not be generated.
7.2
For each PORTB pin, a rising edge detector and a falling
edge detector are present. To enable a pin to detect a
rising edge, the associated IOCBPx bit of the IOCBP
register is set. To enable a pin to detect a falling edge,
the associated IOCBNx bit of the IOCBN register is set.
A pin can be configured to detect rising and falling
edges simultaneously by setting both the IOCBPx bit
and the IOCBNx bit of the IOCBP and IOCBN registers,
respectively.
7.3
The IOCBFx bits located in the IOCBF register are
status flags that correspond to the Interrupt-on-change
pins of PORTB. If an expected edge is detected on an
appropriately enabled pin, then the status flag for that pin
will be set, and an interrupt will be generated if the IOCIE
bit is set. The IOCIF bit of the INTCON register reflects
the status of all IOCBFx bits.
© 2009 Microchip Technology Inc.
INTERRUPT-ON-CHANGE
Enabling the Module
Individual Pin Configuration
Interrupt Flags
Preliminary
7.4
The individual status flags, (IOCBFx bits), can be
cleared by resetting them to zero. If another edge is
detected during this clearing operation, the associated
status flag will be set at the end of the sequence,
regardless of the value actually being written.
In order to ensure that no detected edge is lost while
clearing flags, only AND operations masking out known
changed bits should be performed. The following
sequence is an example of what should be performed.
EXAMPLE 7-1:
7.5
The Interrupt-on-change interrupt sequence will wake
the device from Sleep mode, if the IOCIE bit is set.
If an edge is detected while in Sleep mode, the IOCBF
register will be updated prior to the first instruction
executed out of Sleep.
PIC16F193X/LF193X
ANDWF
MOVLW
XORWF
Clearing Interrupt Flags
Operation in Sleep
0xff
IOCBF, W
IOCBF, F
DS41364C-page 105