PIC16LF88-I/P Microchip Technology, PIC16LF88-I/P Datasheet - Page 38
![IC MCU FLASH 4KX14 EEPROM 18DIP](/photos/6/76/67657/18-dip_300mil__sml.jpg)
PIC16LF88-I/P
Manufacturer Part Number
PIC16LF88-I/P
Description
IC MCU FLASH 4KX14 EEPROM 18DIP
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16LF627A-IP.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC16F87-IP.pdf
(228 pages)
4.PIC16F87-IP.pdf
(8 pages)
5.PIC16F87-IP.pdf
(4 pages)
6.PIC16F87-IP.pdf
(8 pages)
7.PIC16F88-ISO.pdf
(214 pages)
Specifications of PIC16LF88-I/P
Program Memory Type
FLASH
Program Memory Size
7KB (4K x 14)
Package / Case
18-DIP (0.300", 7.62mm)
Core Processor
PIC
Core Size
8-Bit
Speed
10MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
16
Eeprom Size
256 x 8
Ram Size
368 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 7x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC16LF
Core
PIC
Data Bus Width
8 bit
Data Ram Size
368 B
Interface Type
SSP/USART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
16
Number Of Timers
3
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014
Minimum Operating Temperature
- 40 C
On-chip Adc
7-ch x 10-bit
Package
18PDIP
Device Core
PIC
Family Name
PIC16
Maximum Speed
20 MHz
Data Rom Size
256 B
Height
3.3 mm
Length
22.86 mm
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2 V
Width
6.35 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16LF88-I/P
Manufacturer:
Microchip
Quantity:
1 302
PIC16F87/88
FIGURE 4-2:
TABLE 4-2:
DS30487B-page 36
Capacitor values are for design guidance only.
These capacitors were tested with the resonators
listed below for basic start-up and operation. These
values were not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following this table for additional
information.
DD
Note:
Mode
Note 1: See Table 4-2 for typical values of C1 and
HS
XT
and temperature range for the application.
C1
C2
2: A series resistor (R
3: R
(1)
(1)
Typical Capacitor Values Used:
When using resonators with frequencies
above 3.5 MHz, the use of HS mode,
rather than XT mode, is recommended.
HS mode may be used at any V
which the controller is rated. If HS is
selected, it is possible that the gain of the
oscillator will overdrive the resonator.
Therefore, a series resistor should be
placed between the OSC2 pin and the
resonator. As a good starting point, the
recommended value of R
C2.
(typically between 2 M
16.0 MHz
2.0 MHz
4.0 MHz
8.0 MHz
455 kHz
F
RES
R
Freq
S
(2)
varies with the resonator chosen
CERAMIC RESONATORS
(FOR DESIGN GUIDANCE
ONLY)
OSC1
OSC2
CERAMIC RESONATOR
OPERATION (HS OR XT
OSC CONFIGURATION)
R
OSC1
F (3)
S
56 pF
47 pF
33 pF
27 pF
22 pF
) may be required.
to 10 M
S
PIC16F87/88
is 330
To Internal
Logic
SLEEP
.
OSC2
56 pF
47 pF
33 pF
27 pF
22 pF
DD
Preliminary
for
4.3
The ECIO Oscillator mode requires an external clock
source to be connected to the OSC1 pin. There is no
oscillator start-up time required after a Power-on
Reset, or after an exit from SLEEP mode.
In the ECIO Oscillator mode, the OSC2 pin becomes
an additional general purpose I/O pin. The I/O pin
becomes bit 6 of PORTA (RA6). Figure 4-3 shows the
pin connections for the ECIO Oscillator mode.
FIGURE 4-3:
Clock from
Ext. System
External Clock Input
RA6
EXTERNAL CLOCK INPUT
OPERATION
(ECIO CONFIGURATION)
2003 Microchip Technology Inc.
OSC1/CLKI
I/O (OSC2)
PIC16F87/88