PIC16LF873A-I/ML Microchip Technology, PIC16LF873A-I/ML Datasheet - Page 157

• Manufacturer Part Number: PIC16LF873A-I/ML
• Description: IC PIC MCU FLASH 4KX14 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16LF873A-I/ML

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: PIC16LF873A-I/MLR; PIC16LF873A-I/MLR

14.13 Watchdog Timer (WDT)
The Watchdog Timer is a free running, on-chip RC
oscillator which does not require any external
components. This RC oscillator is separate from the
RC oscillator of the OSC1/CLKI pin. That means that
the WDT will run even if the clock on the OSC1/CLKI
and OSC2/CLKO pins of the device has been stopped,
for example, by execution of a SLEEP instruction.
During normal operation, a WDT time-out generates a
device Reset (Watchdog Timer Reset). If the device is
in Sleep mode, a WDT time-out causes the device to
wake-up and continue with normal operation (Watch-
dog Timer Wake-up). The TO bit in the Status register
will be cleared upon a Watchdog Timer time-out.
The WDT can be permanently disabled by clearing
configuration bit, WDTE (Section 14.1 “Configuration
Bits”).
FIGURE 14-11:
TABLE 14-7:
 2003 Microchip Technology Inc.
2007h
81h, 181h
Legend: Shaded cells are not used by the Watchdog Timer.
Note 1:
Address
See Register 14-1 for operation of these bits.
Config. bits
OPTION_REG
Name
SUMMARY OF WATCHDOG TIMER REGISTERS
Note:
WDT Timer
Enable Bit
WDT
WATCHDOG TIMER BLOCK DIAGRAM
PSA and PS2:PS0 are bits in the OPTION_REG register.
From TMR0 Clock Source
(Figure 5-1)
RBPU
Bit 7
(1)
BODEN
INTEDG
0
1
Bit 6
PSA
M
U
X
(1)
T0CS
Bit 5
CP1
0
WDT time-out period values may be found in
Section 17.0 “Electrical Characteristics” under
parameter #31. Values for the WDT prescaler (actually
a postscaler but shared with the Timer0 prescaler) may
be assigned using the OPTION_REG register.
T0SE
Bit 4
CP0
Time-out
MUX
8-to-1 MUX
WDT
Note 1: The CLRWDT and SLEEP instructions
Postscaler
1
2: When a CLRWDT instruction is executed
8
PWRTE
Bit 3
clear the WDT and the postscaler, if
assigned to the WDT and prevent it from
timing out and generating a device Reset
condition.
and the prescaler is assigned to the WDT,
the prescaler count will be cleared but the
prescaler assignment is not changed.
PSA
PSA
To TMR0 (Figure 5-1)
(1)
PIC16F87XA
PS2:PS0
WDTE
Bit 2
PS2
F
Bit 1
DS39582B-page 155
PS1
OSC
1
F
Bit 0
PS0
OSC
0