PIC18F4585-I/PT Microchip Technology, PIC18F4585-I/PT Datasheet - Page 198

• Manufacturer Part Number: PIC18F4585-I/PT
• Description: IC MCU FLASH 24KX16 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4585-I/PT

• Core Size: 8-Bit
• Program Memory Size: 48KB (24K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.25K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3.25KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44PT3 - SOCKET TRAN ICE 44MQFP/TQFPI3-DB18F4680 - BOARD DAUGHTER ICEPIC3AC164305 - MODULE SKT FOR PM3 44TQFP444-1001 - DEMO BOARD FOR PICMICRO MCUAC164020 - MODULE SKT PROMATEII 44TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F2585/2680/4585/4680
17.4
The MSSP module in I
master and slave functions (including general call
support) and provides interrupts on Start and Stop bits
in hardware to determine a free bus (multi-master
function). The MSSP module implements the standard
mode specifications, as well as 7-bit and 10-bit
addressing.
Two pins are used for data transfer:
• Serial clock (SCL) – RC3/SCK/SCL
• Serial data (SDA) – RC4/SDI/SDA
The user must configure these pins as inputs or outputs
through the TRISC<4:3> bits.
FIGURE 17-7:
DS39625C-page 196
RC3/SCK/SCL
RC4/SDI/SDA
I
2
C Mode
Read
Shift
Clock
MSSP BLOCK DIAGRAM
(I
2
2
MSb
C mode fully implements all
C™ MODE)
Stop bit Detect
Match Detect
SSPADD reg
SSPBUF reg
SSPSR reg
Start and
LSb
Write
(SSPSTAT reg)
Set, Reset
Addr Match
Internal
Data Bus
S, P bits
Preliminary
17.4.1
The MSSP module has six registers for I
These are:
• MSSP Control Register 1 (SSPCON1)
• MSSP Control Register 2 (SSPCON2)
• MSSP Status Register (SSPSTAT)
• Serial Receive/Transmit Buffer Register
• MSSP Shift Register (SSPSR) – Not directly
• MSSP Address Register (SSPADD)
SSPCON1, SSPCON2 and SSPSTAT are the control
and status registers in I
SSPCON1 and SSPCON2 registers are readable and
writable. The lower 6 bits of the SSPSTAT are read-only.
The upper two bits of the SSPSTAT are read/write.
SSPSR is the shift register used for shifting data in or
out. SSPBUF is the buffer register to which data bytes
are written to or read from.
SSPADD register holds the slave device address
when the SSP is configured in I
the SSP is configured in Master mode, the lower
seven bits of SSPADD act as the Baud Rate
Generator reload value.
In receive operations, SSPSR and SSPBUF together
create a double-buffered receiver. When SSPSR
receives a complete byte, it is transferred to SSPBUF
and the SSPIF interrupt is set.
During transmission, the SSPBUF is not double-
buffered. A write to SSPBUF will write to both SSPBUF
and SSPSR.
(SSPBUF)
accessible
REGISTERS
© 2007 Microchip Technology Inc.
2
C mode operation. The
2
C Slave mode. When
2
C operation.