DSPIC30F6013A-30I/PF Microchip Technology, DSPIC30F6013A-30I/PF Datasheet - Page 81

• Manufacturer Part Number: DSPIC30F6013A-30I/PF
• Description: IC DSPIC MCU/DSP 132K 80TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F6013A-30I/PF

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 132KB (44K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP, 80-VQFP
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of I/o's: 68
• Flash Memory Size: 132KB
• Supply Voltage Range: 2.5V To 5.5V
• Package: 80TQFP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 68
• Interface Type: CAN/I2C/SPI/UART
• On-chip Adc: 16-chx12-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1AC164314 - MODULE SKT FOR PM3 80PFAC30F001 - MODULE SOCKET DSPIC30F 80TQFPXLT80PT2 - SOCKET TRANSITION ICE 80TQFPDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

11.0
This section describes the second 32-bit General
Purpose Timer module (Timer4/5) and associated
Operational modes. Figure 11-1 depicts the simplified
block diagram of the 32-bit Timer4/5 module.
Figure 11-2 and Figure 11-3 show Timer4/5 configured
as two independent 16-bit timers, Timer4 and Timer5,
respectively.
The Timer4/5 module is similar in operation to the
Timer2/3 module. However, there are some differences
which are as follows:
FIGURE 11-1:
© 2008 Microchip Technology Inc.
Note:
Note:
TIMER4/5 MODULE
T5IF
Event Flag
T4CK
This data sheet summarizes features of
this group of dsPIC30F devices and is not
intended to be a complete reference
source. For more information on the CPU,
peripherals, register descriptions and
general device functionality, refer to the
“dsPIC30F Family Reference Manual”
(DS70046).
Timer configuration bit T32 (T4CON<3>) must be set to ‘
bits are respective to the T4CON register.
(T4CON<6>)
Data Bus<15:0>
Write TMR4
Read TMR4
TGATE
32-BIT TIMER4/5 BLOCK DIAGRAM
dsPIC30F6011A/6012A/6013A/6014A
0
1
Reset
Equal
16
TMR5HLD
TMR5
MSB
PR5
Comparator x 32
16
Q
Q
16
TMR4
LSB
PR4
CK
D
Gate
Sync
T
CY
TGATE (T4CON<6>)
• The Timer4/5 module does not support the ADC
• Timer4/5 can not be utilized by other peripheral
The Operating modes of the Timer4/5 module are
determined by setting the appropriate bit(s) in the
16-bit T4CON and T5CON SFRs.
For 32-bit timer/counter operation, Timer4 is the lsw
and Timer5 is the msw of the 32-bit timer.
event trigger feature
modules, such as input capture and
output compare
Note:
1
’ for a 32-bit timer/counter operation. All control
1 x
0 1
0 0
For 32-bit timer operation, T5CON control
bits are ignored. Only T4CON control bits
are used for setup and control. Timer4
clock and gate inputs are utilized for the
32-bit timer module but an interrupt is
generated with the Timer5 interrupt flag
(T5IF) and the interrupt is enabled with the
Timer5 interrupt enable bit (T5IE).
Sync
TON
TCKPS<1:0>
1, 8, 64, 256
Prescaler
2
DS70143D-page 81