AT91SAM9R64-CU Atmel, AT91SAM9R64-CU Datasheet - Page 662

• Manufacturer Part Number: AT91SAM9R64-CU
• Description: MCU ARM9 64K SRAM 144-LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9R64-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 240MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, POR, PWM, WDT
• Number Of I /o: 49
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 72K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Data Converters: A/D 3x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: 2-Wire, SPI, SSC, USART
• Maximum Clock Frequency: 240 MHz
• Number Of Programmable I/os: 118
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9RL-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 3 Channel
• Controller Family/series: AT91SAM9xxx
• No. Of I/o's: 49
• Ram Memory Size: 64KB
• Cpu Speed: 240MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Package: 144LFBGA
• Device Core: ARM926EJ-S
• Family Name: 91S
• Maximum Speed: 240 MHz
• Operating Supply Voltage: 1.8|3.3 V
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

39.5.2.9
662
AT91SAM9R64/RL64 Preliminary
Equation 1
There is a limitation in the minimum values of VHDLY, HPW and HBP parameters imposed by
the initial latency of the datapath. The total delay in LCDC clock cycles must be higher than or
equal to the latency column in
formula:
where:
The LCDVSYNC is asserted once per frame. This signal is asserted to cause the LCD's line
pointer to start over at the top of the display. The timing of this signal depends on the type of
LCD: STN or TFT LCD.
In STN mode, the high phase corresponds to the complete first line of the frame. In STN mode,
this signal is synchronized with the first active LCDDOTCK rising edge in a line.
In TFT mode, the high phase of this signal starts at the beginning of the first line. The following
timing parameters can be selected:
There are two other parameters to configure in this module, the HOZVAL and the LINEVAL
fields of the LCDFRMCFG:
• Vertical to Horizontal Delay (VHDLY): The delay between begin_of_line and the generation of
• Horizontal Pulse Width (HPW): The LCDHSYNC pulse width is configurable in HPW field of
• Horizontal Back Porch (HBP): The delay between the LCDHSYNC falling edge and the first
• Horizontal Front Porch (HFP): The delay between end of valid data and the end of the line is
• VHDLY, HPW, HBP are the value of the fields of LCDTIM1 and LCDTIM2 registers
• PCLK_PERIOD is the period of LCDDOTCK signal measured in LCDC Clock cycles
• DPATH_LATENCY is the datapath latency of the configuration, given in
• Vertical Pulse Width (VPW): LCDVSYNC pulse width is configurable in VPW field of the
• Vertical Back Porch: Number of inactive lines at the beginning of the frame is configurable in
• Vertical Front Porch: Number of inactive lines at the end of the frame is configurable in VFP
• HOZVAL configures the number of active LCDDOTCK cycles in each line. The number of
LCDHSYNC is configurable in the VHDLY field of the LCDTIM1 register. The delay is equal to
(VHDLY+1) LCDDOTCK cycles.
LCDTIM2 register. The width is equal to (HPW + 1) LCDDOTCK cycles.
LCDDOTCK rising edge with valid data at the LCD Interface is configurable in the HBP field
of the LCDTIM2 register. The delay is equal to (HBP+1) LCDDOTCK cycles.
configurable in the HFP field of the LCDTIM2 register. The delay is equal to (HFP+1)
LCDDOTCK cycles.
654
LCDTIM1 register. The pulse width is equal to (VPW+1) lines.
VBP field of LCDTIM1 register. The number of inactive lines is equal to VBP. This field should
be programmed with 0 in STN Mode.
field of LCDTIM2 register. The number of inactive lines is equal to VFP. This field should be
programmed with 0 in STN mode.
active cycles in each line is equal to (HOZVAL+1) cycles. The minimum value of this
parameter is 1.
(
VHDLY
+
HPW
+
Table 39-2 on page
HBP
+
3
)
×
PCLK_PERIOD
654. This limitation is given by the following
≥
DPATH_LATENCY
Table 39-2 on page
6289C–ATARM–28-May-09