AT91SAM9261B-CU Atmel, AT91SAM9261B-CU Datasheet - Page 36

• Manufacturer Part Number: AT91SAM9261B-CU
• Description: MCU ARM9 ULTRA LOW PWR 217-LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9261B-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 190MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: DMA, LCD, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 192K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Cpu Family: AT91
• Device Core: ARM926EJ-S
• Device Core Size: 32b
• Frequency (max): 240MHz
• Total Internal Ram Size: 160KB
• # I/os (max): 96
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 1.2/1.8/3.3V
• Operating Supply Voltage (max): 1.32/1.95/3.6V
• Operating Supply Voltage (min): 1.08/1.65/2.7/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 217
• Package Type: LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 160 KB
• Interface Type: JTAG,SPI, SSC, TWI, UART
• Maximum Clock Frequency: 190 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 3
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9261-EK
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AT91SAM9xxx
• No. Of I/o's: 96
• Ram Memory Size: 160KB
• Cpu Speed: 190MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• For Use With: AT91SAM9261-EK - KIT EVAL FOR AT91SAM926EJ-S
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

10.7
10.8
10.9
36
Serial Peripheral Interface
Two-wire Interface
USART
AT91SAM9261 Preliminary
• Supports communication with serial external devices
• Master or slave serial peripheral bus interface
• Very fast transfers supported
• Compatibility with standard two-wire serial memory
• One, two or three bytes for slave address
• Sequential read/write operations
• Programmable Baud Rate Generator
• 5- to 9-bit full-duplex synchronous or asynchronous serial communications
• RS485 with driver control signal
• ISO7816, T = 0 or T = 1 Protocols for interfacing with smart cards
• IrDA modulation and demodulation
– Four chip selects with external decoder support allow communication with up to
– Serial memories, such as DataFlash and 3-wire EEPROMs
– Serial peripherals, such as ADCs, DACs, LCD Controllers, CAN Controllers and
– External co-processors
– 8- to 16-bit programmable data length per chip select
– Programmable phase and polarity per chip select
– Programmable transfer delays between consecutive transfers and between clock
– Programmable delay between consecutive transfers
– Selectable mode fault detection
– Transfers with baud rates up to MCK
– The chip select line may be left active to speed up transfers on the same device
– 1, 1.5 or 2 stop bits in Asynchronous Mode or 1 or 2 stop bits in Synchronous Mode
– Parity generation and error detection
– Framing error detection, overrun error detection
– MSB- or LSB-first
– Optional break generation and detection
– By-8 or by-16 over-sampling receiver frequency
– Hardware handshaking RTS-CTS
– Receiver time-out and transmitter timeguard
– Optional Multi-drop Mode with address generation and detection
– NACK handling, error counter with repetition and iteration limit
– Communication at up to 115.2 Kbps
fifteen peripherals
Sensors
and data per chip select
6062LS–ATARM–23-Mar-09