LPC1343FBD48,151 NXP Semiconductors, LPC1343FBD48,151 Datasheet - Page 201

• Manufacturer Part Number: LPC1343FBD48,151
• Description: IC MCU 32BIT 32KB FLASH 48LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC13xxr

Specifications of LPC1343FBD48,151

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-LQFP
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: I²C, Microwire, SPI, SSI, SSP, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 40
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC13
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, UART
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 42
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, KSK-LPC1343
• Development Tools By Supplier: OM11039, OM11040, OM11046, OM11048
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: LPC1000
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Total Internal Ram Size: 8KB
• # I/os (max): 42
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4945; 935289652151

NXP Semiconductors
UM10375
User manual
12.9.2 Master Receiver mode
slave mode. The STA, STO and SI bits must be 0. The SI Bit is cleared by writing 1 to the
SIC bit in the I2CONCLR register. THe STA bit should be cleared after writing the slave
address.
Table 222. I2C0CONSET and I2C1CONSET used to configure Master mode
The first byte transmitted contains the slave address of the receiving device (7 bits) and
the data direction bit. In this mode the data direction bit (R/W) should be 0 which means
Write. The first byte transmitted contains the slave address and Write bit. Data is
transmitted 8 bits at a time. After each byte is transmitted, an acknowledge bit is received.
START and STOP conditions are output to indicate the beginning and the end of a serial
transfer.
The I
I
condition is transmitted, the SI bit is set, and the status code in the I2STAT register is
0x08. This status code is used to vector to a state service routine which will load the slave
address and Write bit to the I2DAT register, and then clear the SI bit. SI is cleared by
writing a 1 to the SIC bit in the I2CONCLR register.
When the slave address and R/W bit have been transmitted and an acknowledgment bit
has been received, the SI bit is set again, and the possible status codes now are 0x18,
0x20, or 0x38 for the master mode, or 0x68, 0x78, or 0xB0 if the slave mode was enabled
(by setting AA to 1). The appropriate actions to be taken for each of these status codes
are shown in
In the master receiver mode, data is received from a slave transmitter. The transfer is
initiated in the same way as in the master transmitter mode. When the START condition
has been transmitted, the interrupt service routine must load the slave address and the
data direction bit to the I
the data direction bit (R/W) should be 1 to indicate a read.
2
Bit
Symbol
Value
Fig 22. Format in the Master Transmitter mode
C logic will send the START condition as soon as the bus is free. After the START
S
from Master to Slave
from Slave to Master
2
C interface will enter master transmitter mode when software sets the STA bit. The
SLAVE ADDRESS
7
-
-
Table 228
All information provided in this document is subject to legal disclaimers.
6
I2EN
1
to
2
Rev. 2 — 7 July 2010
C Data register (I2DAT), and then clear the SI bit. In this case,
Table
RW=0
5
STA
0
231.
A
4
STO
0
DATA
Chapter 12: LPC13xx I2C-bus controller
A = Acknowledge (SDA low)
A = Not acknowledge (SDA high)
S = START condition
P = STOP condition
3
SI
0
n bytes data transmitted
A
2
AA
0
DATA
UM10375
1
-
-
© NXP B.V. 2010. All rights reserved.
A/A
0
-
-
203 of 333
P