C8051T614-GQ Silicon Laboratories Inc, C8051T614-GQ Datasheet - Page 101

• Manufacturer Part Number: C8051T614-GQ
• Description: IC 8051 MCU 8K BYTE-PROG 32-LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051T61xr

Specifications of C8051T614-GQ

• Program Memory Type: OTP
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 29
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051T6x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 29
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051FT610DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 21-ch x 10-bit
• Package: 32LQFP
• Device Core: 8051
• Family Name: C8051T61x
• Maximum Speed: 25 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1441

19.1. Power-On Reset
During power-up, the device is held in a reset state and the RST pin is driven low until V
V
increases (V
power-on and V
cause the device to be released from reset before V
1 ms, the power-on reset delay (T
On exit from a power-on or V
When PORSF is set, all of the other reset flags in the RSTSRC Register are indeterminate (PORSF is
cleared by all other resets). Since all resets cause program execution to begin at the same location
(0x0000) software can read the PORSF flag to determine if a power-up was the cause of reset. The con-
tent of internal data memory should be assumed to be undefined after a power-on reset. The V
is enabled following a power-on reset.
Logic HIGH
RST
Logic LOW
. A delay occurs before the device is released from reset; the delay decreases as the V
DD
DD
ramp time is defined as how fast V
RST
Figure 19.2. Power-On and V
monitor event timing. The maximum V
V
RST
DD
monitor reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1.
Power-On
PORDelay
Reset
T
) is typically less than 0.3 ms.
PORDelay
Rev 1.0
DD
DD
DD
C8051T610/1/2/3/4/5/6/7
reaches the V
ramps from 0 V to V
DD
Monitor Reset Timing
ramp time is 1 ms; slower ramp times may
RST
Monitor
Reset
VDD
level. For ramp times less than
RST
). Figure 19.2. plots the
DD
settles above
DD
VDD
DD
ramp time
monitor
101
t