MC908JL16CFJE Freescale Semiconductor, MC908JL16CFJE Datasheet - Page 98

• Manufacturer Part Number: MC908JL16CFJE
• Description: IC MCU 16K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JL16CFJE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SCI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 26
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: HC08JL
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• Controller Family/series: HC08
• No. Of I/o's: 26
• Ram Memory Size: 512Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• For Use With: DEMO908JL16E - BOARD DEMO FOR MC908JL16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Serial Communications Interface (SCI)
7.8 I/O Registers
These I/O registers control and monitor SCI operation:
7.8.1 SCI Control Register 1
SCI control register 1:
LOOPS — Loop Mode Select Bit
ENSCI — Enable SCI Bit
TXINV — Transmit Inversion Bit
98
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
This read/write bit enables loop mode operation. In loop mode the RxD pin is disconnected from the
SCI, and the transmitter output goes into the receiver input. Both the transmitter and the receiver must
be enabled to use loop mode. Reset clears the LOOPS bit.
This read/write bit enables the SCI and the SCI baud rate generator. Clearing ENSCI sets the SCTE
and TC bits in SCI status register 1 and disables transmitter interrupts. Reset clears the ENSCI bit.
This read/write bit reverses the polarity of transmitted data. Reset clears the TXINV bit.
1 = Loop mode enabled
0 = Normal operation enabled
1 = SCI enabled
0 = SCI disabled
1 = Transmitter output inverted
0 = Transmitter output not inverted
SCI control register 1 (SCC1)
SCI control register 2 (SCC2)
SCI control register 3 (SCC3)
SCI status register 1 (SCS1)
SCI status register 2 (SCS2)
SCI data register (SCDR)
SCI baud rate register (SCBR)
Enables loop mode operation
Enables the SCI
Controls output polarity
Controls character length
Controls SCI wakeup method
Controls idle character detection
Enables parity function
Controls parity type
Address:
Setting the TXINV bit inverts all transmitted values, including idle, break,
start, and stop bits.
Reset:
Read:
Write:
LOOPS
$0013
Bit 7
0
Figure 7-9. SCI Control Register 1 (SCC1)
ENSCI
6
0
MC68HC908JL16 Data Sheet, Rev. 1.1
TXINV
5
0
NOTE
M
4
0
WAKE
3
0
ILTY
2
0
PEN
1
0
Freescale Semiconductor
Bit 0
PTY
0