PIC16LF1827-I/SO Microchip Technology, PIC16LF1827-I/SO Datasheet - Page 321

• Manufacturer Part Number: PIC16LF1827-I/SO
• Description: IC MCU 8BIT 4KB FLASH 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16LF1827-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 18-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 256 x 8
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• On-chip Dac: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

27.0
In-Circuit Serial Programming™ allows customers to
manufacture circuit boards with unprogrammed devices.
Programming can be done after the assembly process
allowing the device to be programmed with the most
recent firmware or a custom firmware. Five pins are
needed for ICSP™ programming:
• ICSPCLK
• ICSPDAT
• MCLR/V
• V
• V
In Program/Verify mode the Program Memory, User
IDs and the Configuration Words are programmed
through serial communications. The ICSPDAT pin is a
bidirectional I/O used for transferring the serial data
and the ICSPCLK pin is the clock input. For more infor-
mation on ICSP™ refer to the “PIC16F/LF1826/27
Memory Programming Specification” (DS41390)
27.1
The device is placed into high-voltage Program/Verify
mode by holding the ICSPCLK and ICSPDAT pins low
then raising the voltage on MCLR/V
FIGURE 27-1:
© 2009 Microchip Technology Inc.
DD
SS
IN-CIRCUIT SERIAL
PROGRAMMING™ (ICSP™)
High-voltage Programming Mode
PP
External
Programming
Signals
TYPICAL CONNECTION FOR ICSP™ PROGRAMMING
Clock
Data
V
V
V
DD
PP
SS
PP
to V
IHH
*
To Normal Connections
.
Preliminary
*
V
DD
27.2
The Low-Voltage Programming mode allows the
PIC16F/LF1826/27 devices to be programmed using
V
Configuration Word 2 is set to ‘1’, the low-voltage ICSP
programming entry is enabled. To disable the
Low-Voltage ICSP mode, the LVP bit must be
programmed to ‘0’.
Entry into the Low-Voltage ICSP Program/Verify modes
requires the following steps:
1.
2.
Once the key sequence is complete, MCLR must be
held at V
maintained.
DD
Note:
*
MCLR is brought to V
A 32-bit key sequence is presented on
ICSPDAT, while clocking ICSPCLK.
only, without high voltage. When the LVP bit of the
10k
PIC16F/LF1826/27
IL
Low-Voltage Programming Mode
for as long as Program/Verify mode is to be
The ICD 2 produces a V
than the maximum V
PIC16F/LF1826/27. When using this pro-
grammer, an external circuit is required to
keep the V
specifications.
*
Isolation devices (as required).
V
MCLR/V
V
ICSPDAT
ICSPCLK
Device to be
Programmed
DD
SS
PP
IL
voltage within the device
PP
.
PP
specification of the
DS41391B-page 321
PP
voltage greater