ATMEGA8535-16MU Atmel, ATMEGA8535-16MU Datasheet - Page 244

• Manufacturer Part Number: ATMEGA8535-16MU
• Description: IC AVR MCU 8K 16MHZ 5V 44-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8535-16MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-VQFN Exposed Pad
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 44MLF EP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• For Use With: ATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

244
ATmega8535(L)
3. Wait until RDY/BSY goes high. (See Figure 117 for signal waveforms)
I. Repeat B through H until the entire Flash is programmed or until all data has been
programmed.
J. End Page Programming
1. 1. Set XA1, XA0 to “10”. This enables command loading.
2. Set DATA to “0000 0000”. This is the command for No Operation.
3. Give XTAL1 a positive pulse. This loads the command, and the internal write sig-
Figure 116. Addressing the Flash which is Organized in Pages
Note:
Figure 117. Programming the Flash Waveforms
Note:
RESET +12V
RDY/BSY
nals are reset.
PAGEL
XTAL1
DATA
XA1
XA0
BS1
BS2
PROGRAM MEMORY
WR
OE
1. PCPAGE and PCWORD are listed in
1. “XX” is don’t care. The letters refer to the programming description above.
PROGRAM
COUNTER
PAGE
0x10
A
PAGE ADDRESS
WITHIN THE FLASH
ADDR. LOW
PCMSB
B
DATA LOW
PCPAGE
C
DATA HIGH
D
E
XX
PAGEMSB
PCWORD
ADDR. LOW
B
WORD ADDRESS
WITHIN A PAGE
Table 104 on page 241
DATA LOW
C
(1)
F
INSTRUCTION WORD
DATA HIGH
D
PAGE
XX
E
ADDR. HIGH
G
(1)
.
H
PCWORD[PAGEMSB:0]:
XX
00
01
02
PAGEEND
2502K–AVR–10/06