ATTINY2313-20SU Atmel, ATTINY2313-20SU Datasheet - Page 126

• Manufacturer Part Number: ATTINY2313-20SU
• Description: IC MCU AVR 2K FLASH 20SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313-20SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Cpu Family: ATtiny
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: SPI/USART/USI
• Total Internal Ram Size: 128Byte
• # I/os (max): 18
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 20
• Package Type: SOIC
• Package: 20SOIC
• Family Name: ATtiny
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 18
• Number Of Timers: 2
• Processor Series: ATTINY2x
• Core: AVR8
• Data Ram Size: 128 B
• Maximum Clock Frequency: 20 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Data Rom Size: 128 B
• Height: 2.35 mm
• Length: 13 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 7.6 mm
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

Asynchronous
Operational Range
126
ATtiny2313
Figure 59. Stop Bit Sampling and Next Start Bit Sampling
The same majority voting is done to the stop bit as done for the other bits in the frame. If the stop
bit is registered to have a logic 0 value, the Frame Error (FE) flag will be set.
A new high to low transition indicating the start bit of a new frame can come right after the last of
the bits used for majority voting. For Normal Speed mode, the first low level sample can be at
point marked (A) in
(C) marks a stop bit of full length. The early start bit detection influences the operational range of
the Receiver.
The operational range of the Receiver is dependent on the mismatch between the received bit
rate and the internally generated baud rate. If the Transmitter is sending frames at too fast or too
slow bit rates, or the internally generated baud rate of the Receiver does not have a similar (see
Table
The following equations can be used to calculate the ratio of the incoming data rate and internal
receiver baud rate.
D
S
S
S
R
Table 49
Normal Speed mode has higher toleration of baud rate variations.
Table 49. Recommended Maximum Receiver Baud Rate Error for Normal Speed Mode (U2X =
0)
F
M
# (Data+Parity Bit)
slow
Sum of character size and parity size (D = 5 to 10 bit)
Samples per bit. S = 16 for Normal Speed mode and S = 8 for Double Speed
mode.
First sample number used for majority voting. S
for Double Speed mode.
Middle sample number used for majority voting. S
S
is the ratio of the slowest incoming data rate that can be accepted in relation to the
receiver baud rate. R
accepted in relation to the receiver baud rate.
49) base frequency, the Receiver will not be able to synchronize the frames to the start bit.
(U2X = 0)
(U2X = 1)
Sample
Sample
M
RxD
R
and
D
= 5 for Double Speed mode.
5
6
7
slow
Table 50
=
------------------------------------------ -
S 1
Figure
–
R
(
D
list the maximum receiver baud rate error that can be tolerated. Note that
+
slow
93.20
94.12
94.81
1
1
+
D S ⋅
59. For Double Speed mode the first low level must be delayed to (B).
(%)
1
2
fast
)S
+
is the ratio of the fastest incoming data rate that can be
3
2
S
F
R
106.67
105.79
4
105.11
fast
5
3
(%)
6
Max Total Error (%)
7
4
8
+5.79/-5.88
+5.11/-5.19
+6.67/-6.8
STOP 1
9
5
F
10
R
= 8 for normal speed and S
M
fast
= 9 for normal speed and
(A)
0/1
6
=
0/1
-----------------------------------
(
D
(B)
0/1
0/1
(
+
D
Recommended Max
Receiver Error (%)
1
+
)S
2
)S
+
S
± 3.0
± 2.5
± 2.0
M
(C)
2543L–AVR–08/10
F
= 4