PIC18F6490-E/PT Microchip Technology, PIC18F6490-E/PT Datasheet - Page 53

• Manufacturer Part Number: PIC18F6490-E/PT
• Description: IC PIC MCU FLASH 16KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6490-E/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, LCD, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-TFQFP
• For Use With: DM163028 - BOARD DEMO PICDEM LCD
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

4.0
The PIC18F6390/6490/8390/8490 devices differentiate
between various kinds of Reset:
a)
b)
c)
d)
e)
f)
g)
h)
This section discusses Resets generated by MCLR,
POR and BOR and covers the operation of the various
start-up timers. Stack Reset events are covered in
Section 5.1.2.4 “Stack Full and Underflow Resets”.
WDT Resets are covered in Section 23.2 “Watchdog
Timer (WDT)”.
A simplified block diagram of the on-chip Reset circuit
is shown in Figure 4-1.
FIGURE 4-1:
© 2007 Microchip Technology Inc.
OSC1
MCLR
V
Note 1: This is the INTRC source from the internal oscillator block and is separate from the RC oscillator of the CLKI pin.
Power-on Reset (POR)
MCLR Reset during normal operation
MCLR Reset during power-managed modes
Watchdog Timer (WDT) Reset (during
execution)
Programmable Brown-out Reset (BOR)
RESET Instruction
Stack Full Reset
Stack Underflow Reset
DD
RESET
2: See Table 4-2 for time-out situations.
Instruction
INTRC
RESET
OST/PWRT
Pointer
32 μs
Stack
( )_IDLE
Brown-out
Time-out
V
(1)
Detect
Sleep
DD
WDT
Reset
Rise
OST
SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
PWRT
Stack Full/Underflow Reset
External Reset
MCLRE
10-Bit Ripple Counter
11-Bit Ripple Counter
POR Pulse
BOREN
1024 Cycles
65.5 ms
PIC18F6390/6490/8390/8490
4.1
Device Reset events are tracked through the RCON
register (Register 4-1). The lower five bits of the
register indicate that a specific Reset event has
occurred. In most cases, these bits can only be set by
the event and must be cleared by the application after
the event. The state of these flag bits, taken together,
can be read to indicate the type of Reset that just
occurred. This is described in more detail in
Section 4.6 “Reset State of Registers”.
The RCON register also has control bits for setting
interrupt priority (IPEN) and software control of the
BOR (SBOREN). Interrupt priority is discussed in
Section 8.0
Section 4.4 “Brown-out Reset (BOR)”.
RCON Register
“Interrupts”.
S
R
BOR
DS39629C-page 51
Q
is
Enable OST
Enable PWRT
Chip_Reset
covered
(2)
in