ST72F324J4B6 STMicroelectronics, ST72F324J4B6 Datasheet - Page 27

• Manufacturer Part Number: ST72F324J4B6
• Description: IC MCU 8BIT 16K FLASH 42-PDIP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F324J4B6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-DIP (0.600", 15.24mm)
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4 bit
• Operating Supply Voltage: 3.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ST7F521-IND/USB, ST7232X-EVAL, ST7MDT20-DVP3, ST7MDT20J-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• For Use With: 497-6421 - BOARD EVAL DGTL BATT CHGR DESIGN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

6.4 SYSTEM INTEGRITY MANAGEMENT (SI)
The System Integrity Management block contains
the Low Voltage Detector (LVD) and Auxiliary Volt-
age Detector (AVD) functions. It is managed by
the SICSR register.
6.4.1 Low Voltage Detector (LVD)
The Low Voltage Detector function (LVD) gener-
ates a static reset when the V
below a V
secures the power-up as well as the power-down
keeping the ST7 in reset.
The V
than the V
to avoid a parasitic reset when the MCU starts run-
ning and sinks current on the supply (hysteresis).
The LVD Reset circuitry generates a reset when
V
The LVD function is illustrated in
The voltage threshold can be configured by option
byte to be low, medium or high.
Provided the minimum V
the oscillator frequency) is above V
can only be in two modes:
Figure 15. Low Voltage Detector vs Reset
DD
– V
– V
RESET
is below:
IT-
IT+
IT-
V
V
reference value for a voltage drop is lower
when V
when V
IT-
IT+
IT+
IT-
reference value for power-on in order
reference value. This means that it
V
DD
DD
DD
is falling
is rising
DD
value (guaranteed for
DD
supply voltage is
Figure
IT-
, the MCU
15.
In these conditions, secure operation is always en-
sured for the application without the need for ex-
ternal reset hardware.
During a Low Voltage Detector Reset, the RESET
pin is held low, thus permitting the MCU to reset
other devices.
Notes:
The LVD allows the device to be used without any
external RESET circuitry.
If the medium or low thresholds are selected, the
detection may occur outside the specified operat-
ing voltage range. Below 3.8V, device operation is
not guaranteed.
The LVD is an optional function which can be se-
lected by option byte.
It is recommended to make sure that the V
ply voltage rises monotonously when the device is
exiting from Reset, to ensure the application func-
tions properly.
V
– under full software control
– in static safe reset
hys
ST72324Jx ST72324Kx
DD
27/164
sup-
1