ST72F324J4B6 STMicroelectronics, ST72F324J4B6 Datasheet - Page 73

• Manufacturer Part Number: ST72F324J4B6
• Description: IC MCU 8BIT 16K FLASH 42-PDIP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F324J4B6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-DIP (0.600", 15.24mm)
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4 bit
• Operating Supply Voltage: 3.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ST7F521-IND/USB, ST7232X-EVAL, ST7MDT20-DVP3, ST7MDT20J-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• For Use With: 497-6421 - BOARD EVAL DGTL BATT CHGR DESIGN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

16-BIT TIMER (Cont’d)
CONTROL REGISTER 2 (CR2)
Read/Write
Reset Value: 0000 0000 (00h)
Bit 7 = OC1E Output Compare 1 Pin Enable.
This bit is used only to output the signal from the
timer on the OCMP1 pin (OLV1 in Output Com-
pare mode, both OLV1 and OLV2 in PWM and
one-pulse mode). Whatever the value of the OC1E
bit, the Output Compare 1 function of the timer re-
mains active.
0: OCMP1 pin alternate function disabled (I/O pin
1: OCMP1 pin alternate function enabled.
Bit 6 = OC2E Output Compare 2 Pin Enable.
This bit is used only to output the signal from the
timer on the OCMP2 pin (OLV2 in Output Com-
pare mode). Whatever the value of the OC2E bit,
the Output Compare 2 function of the timer re-
mains active.
0: OCMP2 pin alternate function disabled (I/O pin
1: OCMP2 pin alternate function enabled.
Note: In Flash devices, this bit is not available for
Timer A. It must be kept at its reset value.
Bit 5 = OPM One Pulse Mode.
0: One Pulse Mode is not active.
1: One Pulse Mode is active, the ICAP1 pin can be
OC1E OC2E OPM PWM CC1 CC0 IEDG2 EXEDG
free for general-purpose I/O).
free for general-purpose I/O).
used to trigger one pulse on the OCMP1 pin; the
active transition is given by the IEDG1 bit. The
length of the generated pulse depends on the
contents of the OC1R register.
7
0
Bit 4 = PWM Pulse Width Modulation.
0: PWM mode is not active.
1: PWM mode is active, the OCMP1 pin outputs a
Bit 3, 2 = CC[1:0] Clock Control.
The timer clock mode depends on these bits:
Table 16. Clock Control Bits
Note: If the external clock pin is not available, pro-
gramming the external clock configuration stops
the counter.
Bit 1 = IEDG2 Input Edge 2.
This bit determines which type of level transition
on the ICAP2 pin will trigger the capture.
0: A falling edge triggers the capture.
1: A rising edge triggers the capture.
Bit 0 = EXEDG External Clock Edge.
This bit determines which type of level transition
on the external clock pin EXTCLK will trigger the
counter register.
0: A falling edge triggers the counter register.
1: A rising edge triggers the counter register.
External Clock (where
programmable cyclic signal; the length of the
pulse depends on the value of OC1R register;
the period depends on the value of OC2R regis-
ter.
Timer Clock
available)
f
f
f
CPU
CPU
CPU
/ 4
/ 2
/ 8
ST72324Jx ST72324Kx
CC1
0
0
1
1
CC0
0
1
0
1
73/164
1