W77E058A40DL Nuvoton Technology Corporation of America, W77E058A40DL Datasheet - Page 44

• Manufacturer Part Number: W77E058A40DL
• Description: IC MCU 8-BIT 32K FLASH 40-DIP
• Manufacturer: Nuvoton Technology Corporation of America
• Series: W77r

Specifications of W77E058A40DL

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: EBI/EMI, Serial Port
• Peripherals: POR, WDT
• Number Of I /o: 32
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP
• Cpu Family: W77
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: UART
• Total Internal Ram Size: 1KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Instruction Set Architecture: CISC
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 40
• Package Type: PDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant

W77E58
9.4 Wait State Control Signal
Either with the software using stretch value to change the required machine cycle of MOVX
instruction, the W77E58 provides another hardware signal WAIT to implement the wider duration of
external data access timing. This wait state control signal is the alternate function of P4.0 such that it
can only be invoked to 44-pin PLCC/QFP package type. The wait state control signal can be enabled
by setting WS (ROMMAP.7) bit. When enabled, the setting of stretch value decides the minimum
length of MOVX instruction cycle and the device will sample the WAIT pin at each C3 state before the
rising edge of read/write strobe signal during MOVX instruction. Once this signal being recongnized,
one more machine cycle (wait state cycle) will be inserted into next cycle. The inserted wait state
cycles are unlimited, so the MOVX instruction cycle will end in which the wait state control signal is
deactivated. Using wait state control signal allows a dynamically access timimg to a selected external
peripheral. The WS bit is accessed by the Timed Access Protection procedure.
Set WS bit ahd stretch value = 0 to enable wait signal.
10. POWER MANAGEMENT
The W77E58 has several features that help the user to control the power consumption of the device.
The power saving features are basically the POWER DOWN mode, ECONOMY mode and the IDLE
mode of operation.
10.1 Idle Mode
The user can put the device into idle mode by writing 1 to the bit PCON.0. The instruction that sets the
idle bit is the last instruction that will be executed before the device goes into Idle Mode. In the Idle
mode, the clock to the CPU is halted, but not to the Interrupt, Timer, Watchdog timer and Serial port
blocks. This forces the CPU state to be frozen; the Program counter, the Stack Pointer, the Program
Status Word, the Accumulator and the other registers hold their contents. The ALE and PSEN pins are
held high during the Idle state. The port pins hold the logical states they had at the time Idle was
activated. The Idle mode can be terminated in two ways. Since the interrupt controller is still active, the
activation of any enabled interrupt can wake up the processor. This will automatically clear the Idle bit,
terminate the Idle mode, and the Interrupt Service Routine(ISR) will be executed. After the ISR,
execution of the program will continue from the instruction which put the device into Idle mode.
The Idle mode can also be exited by activating the reset. The device can be put into reset either by
applying a high on the external RST pin, a Power on reset condition or a Watchdog timer reset. The
external reset pin has to be held high for at least two machine cycles i.e. 8 clock periods to be
recognized as a valid reset. In the reset condition the program counter is reset to 0000h and all the
SFRs are set to the reset condition. Since the clock is already running there is no delay and execution
starts immediately. In the Idle mode, the Watchdog timer continues to run, and if enabled, a time-out
will cause a watchdog timer interrupt which will wake up the device. The software must reset the
Watchdog timer in order to preempt the reset which will occur after 512 clock periods of the time-out.
When the W77E58 is exiting from an Idle mode with a reset, the instruction following the one which
put the device into Idle mode is not executed. So there is no danger of unexpected writes.
10.2 Economy Mode
The power consumption of microcontroller relates to operating frequency. The W77E58 offers a
Economy mode to reduce the internal clock rate dynamically without external components. By default,
one machine cycle needs 4 clocks. In Economy mode, software can select 4, 64 or 1024 clocks per
machine cycle. It keeps the CPU operating at a acceptable speed but eliminates the power
consumption. In the Idle mode, the clock of the core logic is stopped, but all clocked peripherals such
as watchdog timer are still running at a rate of clock/4. In the Economy mode, all clocked peripherals
- 44 -