W77E058A40DL Nuvoton Technology Corporation of America, W77E058A40DL Datasheet - Page 46

• Manufacturer Part Number: W77E058A40DL
• Description: IC MCU 8-BIT 32K FLASH 40-DIP
• Manufacturer: Nuvoton Technology Corporation of America
• Series: W77r

Specifications of W77E058A40DL

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: EBI/EMI, Serial Port
• Peripherals: POR, WDT
• Number Of I /o: 32
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP
• Cpu Family: W77
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: UART
• Total Internal Ram Size: 1KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Instruction Set Architecture: CISC
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 40
• Package Type: PDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant

The W77E58 will exit the Power Down mode with a reset or by an external interrupt pin enabled as
level detect. An external reset can be used to exit the Power down state. The high on RST pin
terminates the Power Down mode, and restarts the clock. The program execution will restart from
0000h. In the Power down mode, the clock is stopped, so the Watchdog timer cannot be used to
provide the reset to exit Power down mode.
The W77E58 can be woken from the Power Down mode by forcing an external interrupt pin activated,
provided the corresponding interrupt is enabled, while the global enable(EA) bit is set and the external
input has been set to a level detect mode. If these conditions are met, then the low level on the
external pin re-starts the oscillator. Then device executes the interrupt service routine for the
corresponding external interrupt. After the interrupt service routine is completed, the program
execution returns to the instruction after the one which put the device into Power Down mode and
continues from there. When RGSL(EXIF.1) bit is set to 1, the CPU will use the internal RC oscillator
instead of crystal to exit Power Down mode. The microcontroller will automatically switch from RC
oscillator to crystal after clock is stable. The RC oscillator runs at approximately 2−4 MHz. Using RC
oscillator to exit from Power Down mode saves the time for waiting crystal start-up. It is useful in the
low power system which usually be awakened from a short operation then returns to Power Down
mode.
Table 5. Status of external pins during Idle and Power Down
11. RESET CONDITIONS
The user has several hardware related options for placing the W77E58 into reset condition. In general,
most register bits go to their reset value irrespective of the reset condition, but there are a few flags
whose state depends on the source of reset. The user can use these flags to determine the cause of
reset using software. There are two ways of putting the device into reset state. They are External reset
and Watchdog reset.
11.1 External Reset
The device continuously samples the RST pin at state C4 of every machine cycle. Therefore the RST
pin must be held for at least 2 machine cycles to ensure detection of a valid RST high. The reset
circuitry then synchronously applies the internal reset signal. Thus the reset is a synchronous
operation and requires the clock to be running to cause an external reset.
Once the device is in reset condition, it will remain so as long as RST is 1. Even after RST is
deactivated, the device will continue to be in reset state for up to two machine cycles, and then begin
program execution from 0000h. There is no flag associated with the external reset condition. However
since the other two reset sources have flags, the external reset can be considered as the default reset
if those two flags are cleared.
The software must clear the POR flag after reading it, otherwise it will not be possible to correctly
determine future reset sources. If the power fails, i.e. falls below Vrst, then the device will once again
go into reset state. When the power returns to the proper operating levels, the device will again
perform a power on reset delay and set the POR flag.
Idle
Idle
Power Down
Power Down
Mode
Program
Memory
External
External
Internal
Internal
ALE
1
1
0
0
PSEN
1
1
0
0
- 46 -
PORT0
Float
Float
Data
Data
PORT1
Data
Data
Data
Data
Address
PORT2
Data
Data
Data
W77E58
PORT3
Data
Data
Data
Data