TMP86FH46ANG(Z) Toshiba, TMP86FH46ANG(Z) Datasheet - Page 155

• Manufacturer Part Number: TMP86FH46ANG(Z)
• Description: IC MCU 8BIT FLASH 16KB 42-SDIP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FH46ANG(Z)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LED, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-SDIP (0.600", 15.24mm)
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: BMSKTOPAS86FH47(AND), BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP86C909XB - EMULATION CHIP FOR TMP86F SDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FH46ANGZ

13. Key-on Wakeup (KWU)
13.1 Configuration
13.2 Control
13.3 Function
Key-on Wakeup Control Register
STOPCR
STOP5) pins.
In details, refer to the following section " 13.2 Control ".
enable/disable in 1-bit unit. When those pins are used for STOP mode release, configure corresponding I/O pins to
input mode by I/O port register beforehand.
"L" level on STOP2 to STOP5 pins, which are enabled by STOPCR, for releasing STOP mode (Note1).
(0031H)
In the TMP86FH46ANG, the STOP mode is released by not only P20(
When the STOP mode is released by STOP2 to STOP5 pins, the
STOP2 to STOP5 pins can controlled by Key-on Wakeup Control Register (STOPCR). It can be configured as
Stop mode can be entered by setting up the System Control Register (SYSCR1), and can be exited by detecting the
STOP mode
release signal
(1: Release)
STOP5
STOP5
STOP4
STOP3
STOP2
7
STOP mode released by STOP5
STOP mode released by STOP4
STOP mode released by STOP3
STOP mode released by STOP2
STOP4
6
INT5
STOP3
Figure 13-1 Key-on Wakeup Circuit
5
STOP2
STOPCR
4
(0031H)
3
Page 141
2
0:Disable
1:Enable
0:Disable
1:Enable
0:Disable
1:Enable
0:Disable
1:Enable
1
STOP
pin needs to be used.
INT5
0
/
STOP
(Initial value: 0000 ****)
) pin but also four (STOP2 to
STOP
STOP2
STOP4
STOP3
STOP5
TMP86FH46ANG
Write
Write
Write
Write
only
only
only
only