DF2378RVFQ34WV Renesas Electronics America, DF2378RVFQ34WV Datasheet - Page 188

• Manufacturer Part Number: DF2378RVFQ34WV
• Description: MCU 3V 512K I-TEMP PB-FREE 144-L
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2300r

Specifications of DF2378RVFQ34WV

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 34MHz
• Connectivity: I²C, IrDA, SCI, SmartCard
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 97
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• For Use With: YLCDRSK2378 - KIT DEV EVAL H8S/2378 LCDYR0K42378FC000BA - KIT EVAL FOR H8S/2378HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)EDK2378 - DEV EVAL KIT FOR H8S/2378
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Section 5 Interrupt Controller
5.4
5.4.1
There are seventeen external interrupts: NMI and IRQ15 to IRQ0. These interrupts can be used to
restore the chip from software standby mode.
NMI Interrupt: Nonmaskable interrupt request (NMI) is the highest-priority interrupt, and is
always accepted by the CPU regardless of the interrupt control mode or the status of the CPU
interrupt mask bits. The NMIEG bit in INTCR can be used to select whether an interrupt is
requested at a rising edge or a falling edge on the NMI pin.
IRQ15 to IRQ0 Interrupts: Interrupts IRQ15 to IRQ0 are requested by an input signal at pins
IRQ15 to IRQ0. Interrupts IRQ15 to IRQ0 have the following features:
• Using ISCR, it is possible to select whether an interrupt is generated by a low level, falling
• Enabling or disabling of interrupt requests IRQ15 to IRQ0 can be selected with IER.
• The interrupt priority level can be set with IPR.
• The status of interrupt requests IRQ15 to IRQ0 is indicated in ISR. ISR flags can be cleared to
When IRQ15 to IRQ0 interrupt requests occur at low level of IRQn, the corresponding IRQ
should be held low until an interrupt handling starts. Then the corresponding IRQ should be set to
high in the interrupt handling routine and clear the IRQnF bit (n = 0 to 15) in ISR to 0. Interrupts
may not be executed when the corresponding IRQ is set to high before the interrupt handling
starts.
Detection of IRQ15 to IRQ0 interrupts does not depend on whether the relevant pin has been set
for input or output. However, when a pin is used as an external interrupt input pin, do not clear the
corresponding DDR to 0 and use the pin as an I/O pin for another function.
A block diagram of interrupts IRQ15 to IRQ0 is shown in figure 5.2.
Rev.7.00 Mar. 18, 2009 page 120 of 1136
REJ09B0109-0700
edge, rising edge, or both edges, at pins IRQ15 to IRQ0.
0 by software.
Interrupt Sources
External Interrupts