PIC17C756-16I/L Microchip Technology, PIC17C756-16I/L Datasheet - Page 223

• Manufacturer Part Number: PIC17C756-16I/L
• Description: MICRO CTRL 16K MEMORY OTP 68PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17C756-16I/L

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: OTP
• Ram Size: 902 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 68-PLCC
• For Use With: AC164308 - MODULE SKT FOR PM3 68PLCCDVA17XL681 - DEVICE ADAPTER FOR PIC17C752DM173001 - KIT DEVELOPMENT PICDEM17AC174007 - MODULE SKT PROMATEII 68PLCCAC164024 - ADAPTER PICSTART PLUS 68PLCC
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -

20.0
Absolute Maximum Ratings †
Ambient temperature under bias................................................................................................................. -55 to +125˚C
Storage temperature .............................................................................................................................. -65˚C to +150˚C
Voltage on V
Voltage on MCLR with respect to V
Voltage on RA2 and RA3 with respect to V
Voltage on all other pins with respect to V
Total power dissipation (Note 1)................................................................................................................................1.0W
Maximum current out of V
Maximum current into V
Input clamp current, I
Output clamp current, I
Maximum output current sunk by any I/O pin (except RA2 and RA3).....................................................................35 mA
Maximum output current sunk by RA2 or RA3 pins ................................................................................................60 mA
Maximum output current sourced by any I/O pin ....................................................................................................20 mA
Maximum current sunk by PORTA and PORTB (combined) .................................................................................150 mA
Maximum current sourced by PORTA and PORTB (combined)............................................................................100 mA
Maximum current sunk by PORTC, PORTD and PORTE (combined) ..................................................................150 mA
Maximum current sourced by PORTC, PORTD and PORTE (combined).............................................................100 mA
Maximum current sunk by PORTF and PORTG (combined) ................................................................................150 mA
Maximum current sourced by PORTF and PORTG (combined) ...........................................................................100 mA
† NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above
those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1997 Microchip Technology Inc.
Note 1: Power dissipation is calculated as follows: Pdis = V
Note 2: Voltage spikes below V
PIC17C752/756 ELECTRICAL CHARACTERISTICS
a series resistor of 50-100 should be used when applying a "low" level to the MCLR pin rather than pulling
this pin directly to V
DD
with respect to V
IK
OK
(V
DD
SS
I
(V
< 0 or V
pin(s) - total (@ 70˚C) ...............................................................................................500 mA
O
pin(s) - total (@ 70˚C) ............................................................................................500 mA
< 0 or V
SS
SS
.
SS
I
SS
................................................................................................................ 0 to +7.5V
> V
at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up. Thus,
O
(Note 2).......................................................................................... -0.3V to +14V
DD
> V
SS
)
SS
DD
.................................................................................... -0.3V to V
............................................................................................. -0.3V to +14V
)
Preliminary
DD
x {I
DD
-
I
OH
} +
{(V
DD
-V
OH
) x I
OH
DS30264A-page 223
} + (V
DD
OL
+ 0.3V
20 mA
20 mA
x I
OL
)