ATMEGA163-8PC Atmel, ATMEGA163-8PC Datasheet - Page 161

• Manufacturer Part Number: ATMEGA163-8PC
• Description: IC AVR MCU 16K A/D 8MHZ 40DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA163-8PC

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

DC Characteristics
T
Notes:
External Clock Drive
Waveforms
1142E–AVR–02/03
A
Symbol
I
V
I
t
CC
ACLK
ACID
ACIO
= -40 C to 85 C, V
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20 mA at Vcc = 5V, 10 mA at Vcc = 3V) under steady state
4. Although each I/O port can source more than the test conditions (3 mA at Vcc = 5V, 1.5 mA at Vcc = 3V) under steady state
5. Minimum V
conditions (non-transient), the following must be observed:
1] The sum of all I
2] The sum of all I
3] The sum of all I
If IOL exceeds the test condition, V
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all I
2] The sum of all I
3] The sum of all I
If IOH exceeds the test condition, V
greater than the listed test condition.
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Initialization Delay
CC
CC
for Power-down is 2.5V.
= 2.7V to 5.5V (unless otherwise noted)
OL
OL
OL
OH
OH
OH
(5)
, for all ports, should not exceed 200 mA.
, for ports B0 - B7, D0 - D7 and XTAL2, should not exceed 100 mA.
, for ports A0 - A7 and C0 - C7 should not exceed 100 mA.
, for all ports, should not exceed 200 mA.
, for ports B0 - B7, D0 - D7 and XTAL2, should not exceed 100 mA.
, for ports A0 - A7 and C0 - C7 should not exceed 100 mA.
(Continued)
Figure 89. External Clock Drive Waveforms
Condition
Active 4 MHz, V
(ATmega163L)
Active 8 MHz, V
(ATmega163)
Idle 4 MHz, V
(ATmega163L)
Idle 8 MHz, V
(ATmega163)
WDT enabled, V
WDT disabled, V
V
V
V
V
V
V
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
OL
CC
CC
OH
may exceed the related specification. Pins are not guaranteed to sink current greater
/2
/2
may exceed the related specification. Pins are not guaranteed to source current
CC
CC
CC
CC
CC
= 3V
= 5V
CC
= 3V
= 5V
= 3V
= 3V
Min
-50
Typ
750
500
<1
9
ATmega163(L)
Max
15.0
15.0
5.0
2.5
4.0
40
50
8
Units
mA
mA
mA
mA
mV
µA
µA
nA
ns
161