TWR-K60N512-KIT Freescale Semiconductor, TWR-K60N512-KIT Datasheet - Page 14

• Manufacturer Part Number: TWR-K60N512-KIT
• Description: TOWER SYSTEM KIT K60N512
• Manufacturer: Freescale Semiconductor
• Series: Kinetisr
• Type: MCUr

Specifications of TWR-K60N512-KIT

• Contents: 4 Boards, Documentation, DVD
• Processor To Be Evaluated: K60
• Data Bus Width: 32 bit
• Interface Type: RS-232, USB, CAN, I2C, SPI, UART
• Dimensions: 3.5 in x 3.5 in x 3.5 in
• Operating Supply Voltage: 1.71 V to 3.6 V
• Silicon Manufacturer: Freescale
• Core Architecture: ARM
• Core Sub-architecture: Cortex - M4
• Silicon Core Number: MK
• Silicon Family Name: Kinetis - K60
• Kit Contents: 4x Brds, Cable, Docs
• Rohs Compliant: Yes
• For Use With/related Products: Freescale Tower System, K60N512
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4 Input/Output Connectors and Pin Usage Table
The following table provides details on which K60N512 pins are using to communicate with the LEDs,
switches, and other I/O interfaces onboard the TWR-K60N512.
Note: Some port pins are used in multiple interfaces on-board and many are potentially connected to
off-board resources via the Primary and Secondary Connectors. Take care to avoid attempted
simultaneous usage of mutually exclusive features.
J10
J12
J9
OSJTAG USB-to-serial
Infrared Port
Pushbuttons
SD Card Slot
Touch Pads
VBAT Power Selection
OSJTAG Mode Selection
JTAG Power Connection
Feature
Bridge
LEDs
TWR-K60N512 Tower Module User's Manual
OSJTAG Bridge RX Data
OSJTAG Bridge TX Data
SD Clock
SD Command
SD Data0
SD Data1
SD Data2
SD Data3
SD Card Detect
SD Write Protect
IR Transmit
IR Receive
SW1 (IRQ0)
SW2 (IRQ1)
SW3 (RESET)
E1 / Touch
E2 / Touch
E3 / Touch
E4 / Touch
E1 / Orange LED
E2 / Yellow LED
E3 / Green LED
Table 6. I/O Connectors and Pin Usage Table
Connection
*OFF*
*OFF*
*1-2*
2-3
ON
ON
Connect VBAT to on-board 3.3V supply
Connect VBAT to the higher voltage between on-board 3.3V
supply or coin-cell supply
OSJTAG bootloader mode (OSJTAG firmware
reprogramming)
Debugger mode
Connect on-board 5V supply to JTAG port (supports
powering board from external JTAG probe)
Disconnect on-board 5V supply from JTAG port
PTE9
PTE8
PTE2
PTE3
PTE1
PTE0
PTE5
PTE4
PTE28
PTE27
PTD7
PTC6
PTA19
PTE26
RESET_b RESET_b
PTA4
PTB3
PTB2
PTB16
PTA11
PTA28
PTA29
Port Pin
UART5_RX
UART5_TX
SDHC0_DCLK
SDHC0_CMD
SDHC0_D0
SDHC0_D1
SDHC0_D2
SDHC0_D3
PTE28
PTE27
CMT_IRO
CMP0_IN0
PTA19
PTE26
TSI0_CH5
TSI0_CH8
TSI0_CH7
TSI0_CH9
PTA11
PTA28
PTA29
Pin Function
Page 14 of 17