20-101-1207 Rabbit Semiconductor, 20-101-1207 Datasheet - Page 47
20-101-1207
Manufacturer Part Number
20-101-1207
Description
RCM4510W FCC CERTIFIED
Manufacturer
Rabbit Semiconductor
Type
Transceiver, 802.15.4/ZigBeer
Datasheet
1.20-101-1207.pdf
(118 pages)
Specifications of 20-101-1207
Frequency
2.4GHz
Wireless Frequency
29.49 MHz
For Use With/related Products
RCM4510W
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
316-1144
- Current page: 47 of 118
- Download datasheet (2Mb)
If a device such as a battery is
connected across two channels
for a differential measurement,
and it is not referenced to
analog ground, then the current
from the device will flow
through both sets of attenuator
resistors without flowing back
to analog ground as shown in
Figure 11. This will generate a
negative voltage at one of the
inputs, ADC1, which will almost
certainly lead to inaccurate A/D
conversions. To make such differential measurements, connect the R1 resistors to the A/D
converter’s internal reference voltage, which is 1.2 V. This internal reference voltage can
be configured in software to be available on pin 6 of header J4 as VREF, and allows you to
convert analog input voltages that are negative with respect to analog ground.
4.4.3 Other Pin Features
There are two other features brought out on the auxiliary I/O header J4.
• There is a +3.3 V power supply point on pin 8, which can deliver up to 25 mA at 3.3 V
• The SYS_PWR_ON signal on pin 9 is used by the XBee RF module to place the
User’s Manual
DC. This power supply point is essentially a filtered and isolated version of the regu-
lated +3.3 V DC power that is supplied to the RCM4510W RabbitCore module through
pin 1 of header J1 from the motherboard.
remaining circuitry on the RCM4510W RabbitCore module into a powered-down
“sleep” mode or to bring it back up to normal operation.
NOTE: This software configuration option for VREF and differential measurements are
NOTE: The amplifier inside the A/D converter’s internal voltage reference circuit has a
not supported at this time.
very limited output-current capability. The internal buffer can source up to 20 mA and
sink only up to 20 µA. Use a separate buffer amplifier if you need to supply any load
current.
Figure 11. Current Flow from Ungrounded
I
or Floating Source
41
Related parts for 20-101-1207
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: