20-101-1207 Rabbit Semiconductor, 20-101-1207 Datasheet - Page 70

• Manufacturer Part Number: 20-101-1207
• Description: RCM4510W FCC CERTIFIED
• Manufacturer: Rabbit Semiconductor
• Type: Transceiver, 802.15.4/ZigBeer

Specifications of 20-101-1207

• Frequency: 2.4GHz
• Wireless Frequency: 29.49 MHz
• For Use With/related Products: RCM4510W
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 316-1144

•
•
64
SLEEPMODE2.C
in the “sleep” mode where most power is removed from the RCM4510W module.
Power is restored once a message is received or after a specified time interval. This
sample program demonstrates waking after a specified time interval.
Sleeping only works on end devices, so the
ENDDEV
sor off and on, a serial terminal emulator is required once the program has been compiled.
Once the XBee RF module on the RCM4510W completes its initialization (it joins the
network), you will be prompted to enter three values that control the XBee RF module's
sleep mode — enter the values followed by the
entered these values via the serial terminal emulator, press any key to initiate the sleep
mode. There will be a delay of a few seconds before the RCM4510W module powers
off. When the RCM4510W module powers back up, it will begin running this program
again from the beginning.
XBEE_GPIO_SERVER.C
and clusters. It is meant to be run with the Windows GUI client (installed in Dynamic C’s
Utilities
sample program (
RabbitCore module or on a single-board computer with a separate XBee RF module.
Compile and run this sample program with the RCM4510W RabbitCore module installed
on the Prototyping Board. Run the Windows GUI client (
Dynamic C
ent to connect to the Digi USB XBee coordinator and scan for devices. Make sure the
RCM4510W and the Digi USB XBee coordinator are configured with the same PAN
ID or extended PAN ID.
If you run the
RF module, set the PAN IDs to match between the client and the server sample programs.
Now select the GPIO server and use the GUI interface on the PC, or the command-line
client on another XBee-equipped board to view the server's inputs and change its outputs.
For example, you can toggle the LEDs on the Prototyping Board on/off.
1. Compile and run the sample program on the RCM4510W module.
2. Once the sample program is running, choose “Close Connection” from the in Dynamic C
3. Connect the
4. Open the serial port in your serial terminal emulator such as TeraTerm or Hyperterminal to connect to
5. Plug the AC adapter back in to apply power to the Prototyping Board once again.
menu, and unplug the AC adapter supply power to the Prototyping Board.
RCM4510 programming header.
the serial port at 57600 baud.
NOTE: This sample program does not demonstrate the saving state. State information
may be saved in battery-backed RAM before the RCM4510W module is placed in the
sleep mode.
in this sample program. Because the XBee RF module turns the Rabbit proces-
Utilities\XBee GPIO GUI
directory) and a Digi USB XBee coordinator or with the GPIO client
XBEE_GPIO_CLIENT.C
DIAG
—This sample program shows how to place the RCM4510W module
SAMPLES/XBEE/XBEE_GPIO_CLIENT.C
connector instead of the
—This sample program shows how to set up and use endpoints
sample program on another board with an XBee
PROG
XBEE_ROLE
folder) on your PC. Configure the GUI cli-
Enter
connector on the programming cable to the
key each time. Once you have
XBEE_GPIO_GUI.exe
macro is set to
) running on an RCM4510W
RabbitCore RCM4500W
NODE_TYPE_
Run
in the