MC33696FCAE Freescale Semiconductor, MC33696FCAE Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/2/262/freescale_semiconductor_sml.jpg)
MC33696FCAE
Manufacturer Part Number
MC33696FCAE
Description
IC UHF RECEIVER PLL TUNED 32-QFN
Manufacturer
Freescale Semiconductor
Type
Transceiverr
Datasheet
1.MC33696FCAE.pdf
(80 pages)
Specifications of MC33696FCAE
Frequency
304, 315, 426, 434, 868 & 915MHz
Data Rate - Maximum
20kbps
Modulation Or Protocol
FSK, OOK
Applications
General Data Transfer
Power - Output
7.5dBm
Sensitivity
-106dBm
Voltage - Supply
2.7 V ~ 3.3 V, 4.5 V ~ 5.5 V
Current - Receiving
10.3mA
Current - Transmitting
13mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
32-QFN
Operating Frequency
915 MHz
Operating Supply Voltage
2.5 V or 3.3 V or 5 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 20 C
Mounting Style
SMD/SMT
Operating Temperature (min)
-20C
Operating Temperature (max)
85C
Operating Temperature Classification
Commercial
Modulation Type
FSK/OOK
Memory Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
12.2.3.2 ID
When clock recovery is done, the data manager verifies if an ID is received. The ID is used to identify a
useful frame to receive. It is also necessary, when the receiver is strobed, to detect an ID in order to stay
in run mode and not miss the frame.
The ID allows selection of the correct device in an RF transmission, as the content has been loaded
previously in the ID register. Its length is variable, defined by the IDL[1:0] bits. The complement of the
ID is also recognized as the identifier.
It is possible to build a tone to form the detection sequence by programming the ID register with a full
sequence of ones or zeroes.
Once the ID is detected, a HEADER will be searched to detect the beginning of the useful data to send on
the SPI port.
See
detected when SOE=1 or SOE=0.
Freescale Semiconductor
Section 12.2.4, “State Machine in Receive Mode When
NOTES:
1. The AGC settling time pulse can be split over different pulses as long as the overall duration is at least 200 μs.
2.
3. The Manchester 0 symbol can be replaced by a 1.
OOK MODULATION (DSREF = 0)
OOK MODULATION (DSREF = 0)
OOK MODULATION (DSREF = 1)
OOK MODULATION (DSREF = 1)
FSK MODULATION (DSREF = 1)
FSK MODULATION (DSREF = 1)
The 200 μs pulse may be replaced by : (1 bit @ 2400 bps or 2 bits @ 4800 bps or 4 bits @ 9600 bps or 8 bits @ 19200 bps).
Table 14
frequencies.
Data Slicer Reference Settling Time
Data Slicer Reference Settling Time
1 NRZ >
1 NRZ >
1 NRZ >
1 NRZ >
defines the minimum number of Manchester symbols required for the data slicer operation versus the data and average filter cut-off
AGC Settling Time
AGC Settling Time
AGC Settling Time
AGC Settling Time
At Least 3 Manchester
At Least 3 Manchester
at Data Rate (2 and 3)
at Data Rate (2 and 3)
200
200
200
200
0 Symbols
0 Symbols
μs (1)
μs (1)
μs (1)
μs (1)
Clock Recovery
Clock Recovery
1 Manchester
1 Manchester
at Data Rate
at Data Rate
‘0’ Symbol
‘0’ Symbol
Data Slicer Reference Settling Time
Data Slicer Reference Settling Time
Figure 9. Preamble Definition
MC33696 Data Sheet, Rev. 12
Clock Recovery
Clock Recovery
at Data Rate (3)
at Data Rate (3)
At Least 3 Manchester
At Least 3 Manchester
at Data Rate (2 and 3)
at Data Rate (2 and 3)
1 Manchester
1 Manchester
0 Symbol
0 Symbol
0 Symbols
0 Symbols
ID
ID
DME=1” for more details when ID is not
ID
ID
Clock Recovery
Clock Recovery
at Data Rate (3)
at Data Rate (3)
1 Manchester
1 Manchester
0 Symbol
0 Symbol
ID
ID
Receive Mode
17