AT86RF231-ZUR Atmel, AT86RF231-ZUR Datasheet - Page 34

• Manufacturer Part Number: AT86RF231-ZUR
• Description: IC RADIO TXRX 2.4GHZ 32-VQFN
• Manufacturer: Atmel

Specifications of AT86RF231-ZUR

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, RF4CE, SP100, WirelessHART™, ISM
• Applications: Industrial Monitoring and Control, Wireless Alarm and Security Systems
• Power - Output: -17dBm ~ 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.3mA
• Current - Transmitting: 14mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 2405 MHz to 2480 MHz
• Interface Type: SPI
• Noise Figure: 6 dB
• Output Power: 20 dB
• Operating Supply Voltage: 2.5 V, 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 12.3 mA
• Minimum Operating Temperature: - 40 C
• Modulation: OQPSK
• Protocol Supported: 802.15.4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

7.1.2
7.1.2.1
8111C–MCU Wireless–09/09
Basic Operating Mode Description
P_ON - Power-On after V
pin 8 (/RST). A successful state change can be verified by reading the radio transceiver status
from register 0x01 (TRX_STATUS).
If TRX_STATUS = 0x1F (STATE_TRANSITION_IN_PROGRESS) the AT86RF231 is on a state
transition. Do not try to initiate a further state change while the radio transceiver is in
STATE_TRANSITION_IN_PROGRESS.
Pin SLP_TR is a multifunctional pin, refer to
(SLP_TR)” on page
causes the following state transitions:
Pin 8 (/RST) causes a reset of all registers (register bits CLKM_CTRL are shadowed, for details
refer to
transceiver into TRX_OFF state. However, if the device was in P_ON state it remains in the
P_ON state.
For all states except SLEEP, the state change commands FORCE_TRX_OFF or TRX_OFF lead
to a transition into TRX_OFF state. If the radio transceiver is in active receive or transmit states
(BUSY_*), the command FORCE_TRX_OFF interrupts these active processes, and forces an
immediate transition to TRX_OFF. In contrast a TRX_OFF command is stored until an active
state (receiving or transmitting) has been finished. After that the transition to TRX_OFF is
performed.
For a fast transition from receive or active transmit states to PLL_ON state the command
FORCE_PLL_ON is provided. In contrast to FORCE_TRX_OFF this command does not disable
the PLL and the analog voltage regulator AVREG. It is not available in states SLEEP, P_ON,
RESET, TRX_OFF, and all *_NOCLK states.
The completion of each requested state change shall always be confirmed by reading the regis-
ter bits TRX_STATUS (register 0x01, TRX_STATUS).
When the external supply voltage (V
goes into the P_ON state performing an on-chip reset. The crystal oscillator is activated and the
default 1 MHz master clock is provided at pin 17 (CLKM) after the crystal oscillator has stabi-
lized. CLKM can be used as a clock source to the microcontroller. The SPI interface and digital
voltage regulator are enabled.
The on-chip power-on-reset sets all registers to their default values. A dedicated reset signal
from the microcontroller at pin 8 (/RST) is not necessary, but recommended for hardware / soft-
ware synchronization reasons.
Whereas the falling edge of pin SLP_TR causes the following state transitions:
• TRX_OFF
• RX_ON
• PLL_ON
• SLEEP
• RX_ON_NOCLK
Section 9.6.4 “Master Clock Signal Output (CLKM)” on page
DD
27. Dependent on the radio transceiver state, a rising edge of pin SLP_TR
⇒
⇒
⇒
⇒
⇒
DD
SLEEP
RX_ON_NOCLK
BUSY_TX
TRX_OFF
RX_ON
) is firstly applied to the AT86RF231, the radio transceiver
Section 6.5 “Sleep/Wake-up and Transmit Signal
(level sensitive)
(level sensitive)
(level sensitive)
(level sensitive)
117) and forces the radio
AT86RF231
34