ATTINY5-MAH Atmel, ATTINY5-MAH Datasheet - Page 118

• Manufacturer Part Number: ATTINY5-MAH
• Description: IC MCU AVR 512B FLASH 8UDFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY5-MAH

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 12MHz
• Peripherals: POR, PWM, WDT
• Number Of I /o: 4
• Program Memory Size: 512B (256 x 16)
• Program Memory Type: FLASH
• Ram Size: 32 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-UFDFN Exposed Pad
• Core: AVR8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

Table 16-1.
Notes:
16.3
118
Symbol
I
CC
1. “Min” means the lowest value where the pin is guaranteed to be read as high.
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. Although each I/O port can sink more than the test conditions (10 mA at V
4. Although each I/O port can source more than the test conditions (10 mA at V
5. The RESET pin must tolerate high voltages when entering and operating in programming modes and, as a consequence,
6. Values are with external clock using methods described in
7. BOD Disabled.
Speed
ATtiny4/5/9/10
conditions (non-transient), the sum of all I
may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test condition.
conditions (non-transient), the sum of all I
may exceed the related specification. Pins are not guaranteed to source current greater than the listed test condition.
has a weak drive strength as compared to regular I/O pins. See
enabled (PRR = 0xFF) and there is no I/O drive.
Parameter
Power Supply Current
Power-down mode
DC Characteristics. T
The maximum operating frequency of the device depends on V
relationship between maximum frequency vs. V
Figure 16-1. Maximum Frequency vs. V
(7)
(6)
A
12 MHz
Condition
Active 1MHz, V
Active 4MHz, V
Active 8MHz, V
Idle 1MHz, V
Idle 4MHz, V
Idle 8MHz, V
WDT enabled, V
WDT disabled, V
8 MHz
4 MHz
= -40°C to +85°C (Continued)
1.8V
OL
OH
CC
CC
CC
(for all ports) should not exceed 60 mA. If I
(for all ports) should not exceed 60 mA. If I
CC
CC
CC
= 2V
= 3V
= 5V
CC
CC
= 2V
= 3V
= 5V
= 3V
= 3V
2.7V
“Minimizing Power Consumption” on page
CC
Min.
Figure 17-25 on page
CC
is linear between 1.8V < V
CC
CC
= 5V, 5 mA at V
4.5V
= 5V, 5 mA at V
Typ.
0.02
0.13
0.15
0.2
0.8
2.7
0.6
4.5
136, and
OL
CC
OH
exceeds the test conditions, V
. As shown in
exceeds the test condition, V
CC
CC
= 3V) under steady state
Figure 17-26 on page
Max.
0.5
1.5
0.2
0.5
1.5
10
5
2
= 3V) under steady state
24. Power Reduction is
CC
5.5V
< 4.5V.
Figure
8127D–AVR–02/10
Units
mA
mA
mA
mA
mA
mA
16-1, the
µA
µA
136.
OH
OL