PIC18F45K80-I/PT Microchip Technology, PIC18F45K80-I/PT Datasheet - Page 302

• Manufacturer Part Number: PIC18F45K80-I/PT
• Description: MCU PIC 32KB FLASH 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F45K80-I/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: ECAN, I²C, LIN, SPI, UART/USART
• Number Of I /o: 35
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.6K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP
• Controller Family/series: PIC18
• Ram Memory Size: 4KB
• Cpu Speed: 16MIPS
• No. Of Pwm Channels: 5
• Embedded Interface Type: I2C, SPI, USART
• Processor Series: PIC18F45K80
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F66K80 FAMILY
21.4
The MSSP module in I
master and slave functions (including general call
support), and provides interrupts on Start and Stop bits
in hardware to determine a free bus (multi-master
function). The MSSP module implements the standard
mode specifications, as well as 7-bit and 10-bit
addressing.
Two pins are used for data transfer:
• Serial Clock (SCL) – RC3/REFO/SCL/SCK
• Serial Data (SDA) – RC4/SDA/SDI
The user must configure these pins as inputs by setting
the associated TRIS bits.
FIGURE 21-7:
DS39977C-page 302
Note:
SDA
SCL
I
Only port I/O names are used in this diagram for
the sake of brevity. Refer to the text for a full list of
multiplexed functions.
2
C Mode
Read
Shift
Clock
MSb
Address Mask
Stop bit Detect
Match Detect
SSPADD reg
SSPBUF reg
MSSP BLOCK DIAGRAM
(I
SSPSR reg
Start and
2
2
C mode fully implements all
C™ MODE)
LSb
Write
Addr Match
Set, Reset
S, P bits
(SSPSTAT reg)
Internal
Data Bus
Preliminary
21.4.1
The MSSP module has seven registers for I
operation. These are:
• MSSP Control Register 1 (SSPCON1)
• MSSP Control Register 2 (SSPCON2)
• MSSP Status Register (SSPSTAT)
• Serial Receive/Transmit Buffer Register
• MSSP Shift Register (SSPSR) – Not directly
• MSSP Address Register (SSPADD)
• I
SSPCON1, SSPCON2 and SSPSTAT are the control
and status registers in I
SSPCON1 and SSPCON2 registers are readable and
writable. The lower 6 bits of the SSPSTAT are read-only.
The upper two bits of the SSPSTAT are read/write.
SSPSR is the shift register used for shifting data in or
out. SSPBUF is the buffer register to which data bytes
are written to or read from.
SSPADD contains the slave device address when the
MSSP is configured in I
MSSP is configured in Master mode, the lower seven
bits of SSPADD act as the Baud Rate Generator reload
value.
SSPMSK holds the slave address mask value when
the module is configured for 7-Bit Address Masking
mode. While it is a separate register, it shares the same
SFR address as SSPADD; it is only accessible when
the SSPM<3:0> bits are specifically set to permit
access.
Section 21.4.3.4 “7-Bit Address Masking Mode”
In receive operations, SSPSR and SSPBUF together,
create a double-buffered receiver. When SSPSR
receives a complete byte, it is transferred to SSPBUF
and the SSPIF interrupt is set.
During
double-buffered. A write to SSPBUF will write to both
SSPBUF and SSPSR.
(SSPBUF)
accessible
2
C Slave Address Mask Register (SSPMSK)
transmission,
Additional
REGISTERS
 2011 Microchip Technology Inc.
details
2
C Slave mode. When the
the
2
C mode operation. The
SSPBUF
are
provided
is
.
not
2
in
C