PCA9634PW NXP Semiconductors, PCA9634PW Datasheet - Page 7

• Manufacturer Part Number: PCA9634PW
• Description: IC, LED DRIVER, RGBA, 20-TSSOP
• Manufacturer: NXP Semiconductors

Specifications of PCA9634PW

• No. Of Outputs: 8
• Output Current: 25mA
• Output Voltage: 5.5V
• Input Voltage: 2.3V To 5.5V
• Dimming Control Type: PWM
• Driver Case Style: TSSOP
• Switching Frequency: 1MHz
• Base Number: 9634
• Operating: RoHS Compliant
• Number Of Segments: 16
• Low Level Output Current: 200 mA
• High Level Output Current: 50 uA
• Operating Supply Voltage: 2.3 V to 5.5 V
• Maximum Supply Current: 10 mA
• Maximum Power Dissipation: 400 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: TSSOP-20
• Minimum Operating Temperature: - 40 C
• Led Driver Application: RGB Or RGBA LED Drivers, LED Status Information, Displays, Backlights
• Rohs Compliant: Yes
• Lead Free Status / Rohs Status: Details

NXP Semiconductors
7. Functional description
PCA9634_6
Product data sheet
7.1.1 Regular I
7.1 Device addresses
Refer to
Following a START condition, the bus master must output the address of the slave it is
accessing.
There are a maximum of 128 possible programmable addresses using the 7 hardware
address pins. Two of these addresses, Software Reset and LED All Call, cannot be used
because their default power-up state is ON, leaving a maximum of 126 addresses. Using
other reserved addresses, as well as any other Sub Call address, will reduce the total
number of possible addresses even further.
The I
internal pull-up resistors are incorporated on the hardware selectable address pins and
they must be pulled HIGH or LOW.
Remark: Using reserved I
devices are on the bus and/or the bus will be open to other I
date. In a closed system where the designer controls the address assignment these
addresses can be used since the PCA9634 treats them like any other address. The
LED All Call, Software Rest and PCA9564 or PCA9665 slave address (if on the bus) can
never be used for individual device addresses.
The last bit of the address byte defines the operation to be performed. When set to logic 1
a read is selected, while a logic 0 selects a write operation.
Fig 5.
•
•
•
•
•
•
PCA9634 LED All Call address (1110 000) and Software Reset (0000 0110) which
are active on start-up
PCA9564 (0000 000) or PCA9665 (1110 000) slave address which is active on
start-up
‘reserved for future use’ I
slave devices that use the 10-bit addressing scheme (1111 0XX)
slave devices that are designed to respond to the General Call address (0000 000)
High-speed mode (Hs-mode) master code (0000 1XX).
2
C-bus slave address of the PCA9634 is shown in
Figure 1 “Block diagram of
Slave address
2
C-bus slave address
Rev. 06 — 12 September 2008
2
C-bus addresses will interfere with other devices, but only if the
2
C-bus addresses (0000 011, 1111 1XX)
A6
A5
hardware selectable
PCA9634”.
slave address
A4
A3
A2
A1
002aab319
A0
Figure
R/W
8-bit Fm+ I
2
C-bus systems at some later
5. To conserve power, no
PCA9634
2
© NXP B.V. 2008. All rights reserved.
C-bus LED driver
7 of 38