C40K-CDR-A Omron, C40K-CDR-A Datasheet - Page 193
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
C40K-CDR-A
Manufacturer Part Number
C40K-CDR-A
Description
PROGRAMMABLE CONTROLLER CPU
Manufacturer
Omron
Datasheet
1.C28P-EDR-A.pdf
(225 pages)
Specifications of C40K-CDR-A
Leaded Process Compatible
No
Peak Reflow Compatible (260 C)
No
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 193 of 225
- Download datasheet (2Mb)
System Operations
*Modes in which the given instruction is applicable: R = RUN, M = MONITOR, P = PROGRAM
Data Clear
Address Designation
Program Search
Instruction Insert
Instruction Delete
Program Check
Error Message Read
Bit/Word Monitor
Forced Set/Reset
Hex/BCD Data Change
SV Change
SV Reset
Program Memory Save
Program Memory Restore
Program Memory Compare
Data Clear
Unless otherwise specified, this
operation will clear all erasable
memory in Program Memory and
IR, HR, AR, DM, and TC areas. To
clear EPROM memory the write
enable switch must be ON (i.e.,
enabled). The branch lines shown
are used only when performing a
partial memory clear, with each of
the memory areas entered being
retained. Specifying an address will
result in the Program Memory after
and including that address being
deleted. All memory up to that
address will be retained.
Operation/Description
Name
Programming Console Operations
Used to erase data, either selectively or totally, from the Program Memory and
the IR, AR, HR, DM, and TC areas.
Displays the specified address.
Searches a program for the specified data address or instruction.
Allows a new instruction to be inserted before the displayed instruction, or
deletes the displayed instruction (respectively).
Checks the completed program for syntax errors (up to three levels in H-type
PCs).
Displays error messages in sequence, starting with the most severe messages. 148
Displays the specified address whose operand is to be monitored. In RUN or
MONTR mode it will show the status of the operand for any bit or word in any
data area.
Set: Used to turn ON bits or timers, or to increment counters currently
displayed on the left of the screen.
Reset: Used to turn OFF bits, or to reset timers or counters.
Used to change the value of the leftmost BCD or hexadecimal word displayed
during a Bit/Word Monitor operation.
Alters the SV of a timer or counter either by incrementing or decrementing the
value, or by overwriting the original value with a new one.
Saves Program Memory to tape.
Reads Program Memory from tape.
Compares Program Memory data on tape with that in the Program Memory
area.
P
Modes*
CLR
Appendix C
PLAY
SET
NOT
Function
RESET
REC
Key sequence
All Clear
[Address]
CNT
DM
HR
Partial
Clear
MONTR
Retained if
pressed
47
50
55
57
53
150
153
155
156
158
159
159
Page
183
Related parts for C40K-CDR-A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G4A-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G5NB-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6B-2114P-US](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6D-1A-ASI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G8P-1A4P](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: