MCR-C-UI-UI-DCI-NC Phoenix Contact, MCR-C-UI-UI-DCI-NC Datasheet
MCR-C-UI-UI-DCI-NC
Specifications of MCR-C-UI-UI-DCI-NC
Related parts for MCR-C-UI-UI-DCI-NC
MCR-C-UI-UI-DCI-NC Summary of contents
Page 1
... The required auxiliary voltage is indicated via a green power LED. This clearly indicates whether or not auxiliary voltage is available. The MCR module ensures the safe decoupling of a sensor circuit from the evaluation circuit and also prevents the nega- tive effects of several sensor circuits connected with one another ...
Page 2
... ±2 ± ± ± ... ... ... ± ± ± ... ... 100238_en_02 Type MCR-C-UI-UI-DCI MCR-C-UI-UI-450-DCI MCR-C-UI-UI-DCI-NC Input IN03 IN18 -1 ... +1 V IN28 0 ... 500 IN19 -2 ... +2 V IN29 0 ... IN20 -2.5 ... +2.5 V IN30 0 ... IN21 -5 ... +5 V IN31 0 ... 2 IN22 -10 ... +10 V IN32 0 ... IN23 -20 ... +20 V IN33 -5 ... + ... 60 mV IN34 -10 ... +10 mA OUT14 = = IN25 0 ...
Page 3
... Load/output load voltage output Load/output load current output Power supply Supply voltage range Max. current consumption General data Limit frequency (3 dB) MCR-C-UI-UI-DCI MCR-C-UI-UI-DCI-NC Limit frequency (3 dB) MCR-C-UI-UI-450-DCI Measuring principle Transmission error, max. Maximum temperature coefficient Alignment zero Alignment span Step response (10-90%) ...
Page 4
... GND 1 100238_en_02 1.5 kV (50 Hz, 1 min (50 Hz, 1 min.) -20 °C ... 65 °C CE compliant Class I, Div. 2, Groups non-hazardous locations Germanischer Lloyd EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 55011 OUT OUT U GND 2 9 +24V DC 10 GND 3 11 GND 3 12 MCR-C-UI-UI(-450)-DCI(-NC) Class A 4 PHOENIX CONTACT ...
Page 5
... CAUTION: Electrostatic discharge The module contains components that can be damaged or destroyed by electrostatic discharge. When hand- ling the module, observe the necessary safety precautions against electrostatic discharge (ESD) according to EN 61340-5-1 and EN 61340-5-2. 100238_en_02 MCR-C-UI-UI(-450)-DCI(-NC) 5 PHOENIX CONTACT ...
Page 6
... The current measuring transducer is connected to the power supply at the "+24VDC" and "GND" connection terminal blocks (see block diagram). 100238_en_02 DIP switches S1 and S2 are located inside the housing Supply voltage 2 Output: Standard signals 1 3 "ZERO" and "SPAN" potentiometers 4 "POWER" LED 5 Input: Standard signals 6 Universal snap-on foot for EN DIN rails MCR-C-UI-UI(-450)-DCI(-NC) 6 PHOENIX CONTACT ...
Page 7
... Insert the wires in the corresponding connection terminal block. Use a screwdriver to tighten the screw in the opening above the connection terminal block MCR-C-UI-UI(-450)-DCI(-NC) WARNING In potentially explosive areas, snap the modu- le onto the DIN rail and connect the cables only when the power is disconnected. PHOENIX CONTACT 7 ...
Page 8
... Both potentiometers are located on the top of the module. ATTENTION: Module can become damaged Before commencing the adjustment process, observe the warm-up phase of two minutes. MCR-C-UI-UI(-450)-DCI(-NC) 8 PHOENIX CONTACT ...
Page 9
... Output final value 5 V Adjustment tolerance ±0.5 mV 100238_en_02 0 ... 10 V Output DIP 2 DIP ... 5 mA Output 0 ... 10 mA Output DIP 2 DIP ±10 V Output 1 ... 5 V Output ±0.5 mV ±1 mV MCR-C-UI-UI(-450)-DCI(-NC) ±5 V Output ±10 V Output DIP ... 20 mA Output DIP ... 20 mA Output 4 ... 20 mA Output ±1 μA ±1 μA ...
Page 10
... Specifying the Input Signal Range via DIP Switch 1 Specifying the Output Signal Range via DIP Switch 2 100238_en_02 MCR-C-UI-UI(-450)-DCI(-NC) Select one of the possible signal ranges using the appropri- ate configuration of DIP switch 1 according to the table. Exception: Bipolar input signals are not permitted for the 4 … ...
Page 11
... MCR-C-UI-UI(-450)-DCI(-NC) Output With Adjustment Point Calculation (±5 V/± ... 5 V/0 ... 5 mA/0 ... 10 mA/0 ... 20 mA/4 ... 20 mA) Set the output range via DIP switch 2. Please note the selec- ted input range. Specify the initial and final value of the input signal using a calibration device. ...
Page 12
... Level sensor 0...20mA 24V Application example: Level measurement PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany 100238_en_02 MCR-C-UI-UI-DCI 1 U/I 2 GND 1 3 GND 1 Phone: +49-(0) 5235-3-00 • Fax: +49-(0) 5235-3 www.phoenixcontact.com MCR-C-UI-UI(-450)-DCI(-NC) OUT POWER (+) 24V GND 3 24V 9 12 ...