LAN91C96TQFP SMSC, LAN91C96TQFP Datasheet - Page 46
![Ethernet ICs Non-PCI 10 Mbps Ethernet MAC](/photos/27/13/271359/lan9116_sml.jpg)
LAN91C96TQFP
Manufacturer Part Number
LAN91C96TQFP
Description
Ethernet ICs Non-PCI 10 Mbps Ethernet MAC
Manufacturer
SMSC
Type
Single Chip MAC and PHY Controllerr
Datasheet
1.LAN91C96-MU.pdf
(125 pages)
Specifications of LAN91C96TQFP
Ethernet Connection Type
10 Base-T, 100 Base-TX
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Product
Ethernet Controllers
Number Of Transceivers
1
Standard Supported
802.3, 802.3u
Data Rate
10 Mbps, 100 Mbps
Supply Voltage (max)
5 V
Supply Voltage (min)
0 V
Supply Current (max)
95 mA
Maximum Operating Temperature
+ 70 C
Package / Case
TQFP-100
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Revision 1.0 (10-24-08)
WAKEUP - When this bit is set, it indicates that a receive packet was received that had the “Magic” packet
(MP) signature of the node’s own Individual address repetitions in it. This bit indicates a valid detection for
magic packet.
TX_DEFR - Transmit Deferred. When set, carrier was detected during the first 6.4 uSec of the inter frame
gap. Cleared at the end of every packet sent.
LTX_BRD - Last transmit frame was a broadcast. Set if frame was broadcast. Cleared at the start of every
transmit frame.
SQET - Signal Quality Error Test. The transmitter opens a 1.6 us window 0.8 us after transmission is
completed and the receiver returns inactive. During this window, the transmitter expects to see the SQET
signal from the transceiver. The absence of this signal is a 'Signal Quality Error' and is reported in this
status bit. Transmission stops and EPH INT is set if STP_SQET is in the TCR is also set when SQET is
set. This bit is cleared by setting TXENA high.
16COL - 16 collisions reached. Set when 16 collisions are detected for a transmit frame. TXENA bit in TCR
is reset. Cleared when TXENA is set high.
LTX_MULT - Last transmit frame was a multicast. Set if frame was a multicast. Cleared at the start of
every transmit frame.
MULCOL - Multiple collision detected for the last transmit frame. Set when more than one collision was
experienced. Cleared when TX_SUC is high at the end of the packet being sent.
SNGLCOL - Single collision detected for the last transmit frame. Set when a collision is detected. Cleared
when TX_SUC is high at the end of the packet being sent.
TX_SUC - Last transmit was successful. Set if transmit completes without a fatal error. This bit is cleared
by the start of a new frame transmission or when TXENA is set high.
Fatal errors are:
I/O SPACE - BANK0
SOFT_RST - Software activated Reset. Active high. Initiated by writing this bit high and terminated by
writing the bit low. The LAN91C96 configuration is not preserved, except for Configuration, Base, and IA0-
5 Registers. The EEPROM in both LOCAL BUS and PCMCIA mode is not reloaded after software reset.
SOFT
OFFSET
RST
0
0
16 collisions
SQET fail and STP_SQET = 1
Carrier lost and MON_CSN = 1
Late collision
4
FILT
CAR
0
0
RECEIVE CONTROL REGISTER
0
0
0
DATASHEET
NAME
0
0
0
Page 46
Non-PCI Single-Chip Full Duplex Ethernet Controller with Magic Packet
0
0
0
ALMUL
READ/WRITE
0
0
0
TYPE
STRIP
PRMS
CRC
0
0
SYMBOL
SMSC LAN91C96 5v&3v
RCR
ABORT
RXEN
RX_
0
0
Datasheet