XC3S500E-4PQG208C Xilinx Inc, XC3S500E-4PQG208C Datasheet - Page 96
![FPGA Spartan®-3E Family 500K Gates 10476 Cells 572MHz 90nm (CMOS) Technology 1.2V 208-Pin PQFP](/photos/6/71/67100/pq208_sml.jpg)
XC3S500E-4PQG208C
Manufacturer Part Number
XC3S500E-4PQG208C
Description
FPGA Spartan®-3E Family 500K Gates 10476 Cells 572MHz 90nm (CMOS) Technology 1.2V 208-Pin PQFP
Manufacturer
Xilinx Inc
Series
Spartan™-3Er
Datasheet
1.XC3S100E-4VQG100C.pdf
(233 pages)
Specifications of XC3S500E-4PQG208C
Package
208PQFP
Family Name
Spartan®-3E
Device Logic Cells
10476
Device Logic Units
1164
Device System Gates
500000
Number Of Registers
9312
Maximum Internal Frequency
572 MHz
Typical Operating Supply Voltage
1.2 V
Maximum Number Of User I/os
158
Ram Bits
368640
Number Of Logic Elements/cells
10476
Number Of Labs/clbs
1164
Total Ram Bits
368640
Number Of I /o
158
Number Of Gates
500000
Voltage - Supply
1.14 V ~ 1.26 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
208-BFQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
122-1536 - KIT STARTER SPARTAN-3E
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
122-1520
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XC3S500E-4PQG208C
Manufacturer:
XILINX
Quantity:
362
Company:
Part Number:
XC3S500E-4PQG208C
Manufacturer:
Xilinx Inc
Quantity:
10 000
Part Number:
XC3S500E-4PQG208C
Manufacturer:
XILINX/赛灵思
Quantity:
20 000
Functional Description
can also be eliminated from the interface. However,
RDWR_B must remain Low during configuration.
After configuration, all of the interface pins except DONE
and PROG_B are available as user I/Os. Alternatively, the
bidirectional SelectMAP configuration interface is available
after configuration. To continue using SelectMAP mode, set
the Persist bitstream generator option to Yes. The external
host can then read and verify configuration data.
Table 65: Slave Parallel Mode Connections
96
HSWAP
M[2:0]
D[7:0]
BUSY
CSI_B
RDWR_B
CCLK
CSO_B
Pin Name
FPGA Direction
Output
Output
Input
Input
Input
Input
Input
Input
User I/O Pull-Up Control. When
Low during configuration, enables
pull-up resistors in all I/O pins to
respective I/O bank V
0: Pull-ups during configuration
1: No pull-ups
Mode Select. Selects the FPGA
configuration mode. See
Considerations for the HSWAP,
M[2:0], and VS[2:0]
Data Input.
Busy Indicator.
Chip Select Input. Active Low.
Read/Write Control. Active Low
write enable.
Configuration Clock. If CCLK PCB
trace is long or has multiple
connections, terminate this output to
maintain signal integrity. See
Design
Chip Select Output. Active Low.
Considerations.
Description
Pins.
CCO
www.xilinx.com
Design
input.
CCLK
The Persist option will maintain A20-A23 as configuration
pins although they are not used in SelectMAP mode.
The Slave Parallel mode is also used with BPI mode to cre-
ate multi-FPGA daisy-chains. The lead FPGA is set for BPI
mode configuration; all the downstream daisy-chain FPGAs
are set for Slave Parallel configuration, as highlighted in
Figure
Drive at valid logic level
throughout configuration.
M2 = 1, M1 = 1, M0 = 0 Sampled
when INIT_B goes High.
Byte-wide data provided by host.
FPGA captures data on rising
CCLK edge.
If CCLK frequency is < 50 MHz,
this pin may be ignored. When
High, indicates that the FPGA is
not ready to receive additional
configuration data. Host must
hold data an additional clock
cycle.
Must be Low throughout
configuration.
Must be Low throughout
configuration.
External clock.
Not used in single FPGA
applications. In a daisy-chain
configuration, this pin connects to
the CSI_B pin of the next FPGA in
the chain. Actively drives.
59.
During Configuration
DS312-2 (v3.8) August 26, 2009
User I/O
User I/O
User I/O. If bitstream
option Persist=Yes,
becomes part of
SelectMap parallel
peripheral interface.
User I/O. If bitstream
option Persist=Yes,
becomes part of
SelectMap parallel
peripheral interface.
User I/O. If bitstream
option Persist=Yes,
becomes part of
SelectMap parallel
peripheral interface.
User I/O. If bitstream
option Persist=Yes,
becomes part of
SelectMap parallel
peripheral interface.
User I/O If bitstream
option Persist=Yes,
becomes part of
SelectMap parallel
peripheral interface.
User I/O
After Configuration
Product Specification
R