PSD834F2-15M STMicroelectronics, PSD834F2-15M Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
PSD834F2-15M
Manufacturer Part Number
PSD834F2-15M
Description
Manufacturer
STMicroelectronics
Datasheet
1.PSD834F2-15M.pdf
(95 pages)
Specifications of PSD834F2-15M
Operating Temperature (max)
70C
Operating Temperature (min)
0C
Operating Temperature Classification
Commercial
Package Type
PQFP
Mounting
Surface Mount
Pin Count
52
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Programming Flash Memory
Flash memory must be erased prior to being pro-
grammed. A byte of Flash memory is erased to all
1s (FFh), and is programmed by setting selected
bits to '0.' The MCU may erase Flash memory all
at once or by-sector, but not byte-by-byte. Howev-
er, the MCU may program Flash memory byte-by-
byte.
The primary and secondary Flash memories re-
quire the MCU to send an instruction to program a
byte or to erase sectors (see Table 7).
Once the MCU issues a Flash memory Program or
Erase instruction, it must check for the status bits
for completion. The embedded algorithms that are
invoked inside the PSD support several means to
provide status to the MCU. Status may be checked
using any of three methods: Data Polling, Data
Toggle, or Ready/Busy (PC3).
Data Polling. Polling on the Data Polling Flag
(DQ7) Bit is a method of checking whether a Pro-
gram or Erase cycle is in progress or has complet-
ed. Figure 4 shows the Data Polling algorithm.
When the MCU issues a Program instruction, the
embedded algorithm within the PSD begins. The
MCU then reads the location of the byte to be pro-
grammed in Flash memory to check status. The
Data Polling Flag (DQ7) Bit of this location be-
comes the complement of b7 of the original data
byte to be programmed. The MCU continues to
poll this location, comparing the Data Polling Flag
(DQ7) Bit and monitoring the Error Flag (DQ5) Bit.
When the Data Polling Flag (DQ7) Bit matches b7
of the original data, and the Error Flag (DQ5) Bit
remains '0,' the embedded algorithm is complete.
If the Error Flag (DQ5) Bit is '1,' the MCU should
test the Data Polling Flag (DQ7) Bit again since
the Data Polling Flag (DQ7) Bit may have changed
simultaneously with the Error Flag (DQ5) Bit (see
Figure 4).
The Error Flag (DQ5) Bit is set if either an internal
time-out occurred while the embedded algorithm
attempted to program the byte or if the MCU at-
tempted to program a '1' to a bit that was not
erased (not erased is logic 0).
It is suggested (as with all Flash memories) to read
the location again after the embedded program-
ming algorithm has completed, to compare the
byte that was written to the Flash memory with the
byte that was intended to be written.
When using the Data Polling method during an
Erase cycle, Figure 4 still applies. However, the
Data Polling Flag (DQ7) Bit is '0' until the Erase cy-
cle is complete. A '1' on the Error Flag (DQ5) Bit in-
dicates a time-out condition on the Erase cycle; a
'0' indicates no error. The MCU can read any loca-
tion within the sector being erased to get the Data
Polling Flag (DQ7) Bit and the Error Flag (DQ5)
Bit.
PSDsoft Express generates ANSI C code func-
tions which implement these Data Polling algo-
rithms.
Figure 4. Data Polling Flowchart
at VALID ADDRESS
NO
READ DQ5 & DQ7
READ DQ7
START
DATA
DATA
DQ7
DQ5
DQ7
FAIL
= 1
=
=
YES
NO
NO
YES
YES
PSD834F2V
PASS
AI01369B
19/95