PAXLSG00 Red Lion Controls, PAXLSG00 Datasheet - Page 4

• Manufacturer Part Number: PAXLSG00
• Description: METER STRAIN GAGE 3 1/2-DIGIT
• Manufacturer: Red Lion Controls
• Series: PAX®LITEr
• Type: Strain Gage, Millivolt Meterr

Specifications of PAXLSG00

• Measuring Range: ±2V
• Display Style: Red Characters, Black Background
• Display Type: LED
• Display Face Size: 3.80" L x 1.95" W (96.5 x 49.5mm)
• Display Digits: 3.5
• Display Digits - Height: 0.560" (14.22mm)
• Mounting Type: Panel Mount
• Termination: Terminal Block
• Voltage - Supply: 85 ~ 250VAC
• No. Of Digits / Alpha: 3-1/2
• Meter Range: 0mV To 10mV / 0V To 2V
• Digit Height: 14.2mm
• Power Consumption: 6VA
• Operating Temperature Range: 0°C To +60°C
• Supply Voltage Ac, Min: 85V
• Signal Input Type: Strain Gage
• Character Size: 0.56"
• Display Font Color: Red
• Rohs Compliant: NA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: RLC114

Installation
unit is intended to be mounted into an enclosed panel. Prepare the panel cutout
to the dimensions shown. Remove the panel latch from the unit. Slide the panel
applying power. To access the switches, remove the meter base from the case by
firmly squeezing and pulling back on the side rear finger tabs. This should lower
the latch below the case slot (which is located just in front of the finger tabs). It
is recommended to release the latch on one side, then start the other side latch.
Excitation Range Jumper
only one jumper position is used at a time.
1.0 I
2.0 S
PAXLSG Jumper Selection
The PAX meets NEMA 4X/IP65 requirements when properly installed. The
The meter has switches that must be checked and/or changed prior to
A jumper is used for selection of the 5 or 10 volt range. It is important that
NSTALLING THE
ETTING THE
JUMPER SELECTIONS
The
indicates factory setting.
gasket over the rear of the unit to the back of
the bezel. The unit should be installed
fully assembled. Insert the unit into
the panel cutout.
S
WITCHES AND
M
ETER
4
so that the tabs of the panel latch engage in the slots on the case. The panel latch
should be engaged in the farthest forward slot possible. To achieve a proper seal,
tighten the latch screws evenly until the unit is snug in the panel (Torque to
approximately 7 in-lbs [79N-cm]). Do not over-tighten the screws.
Installation Environment
operating temperature and provides good air circulation. Placing the unit near
devices that generate excessive heat should be avoided.
Do NOT use solvents. Continuous exposure to direct sunlight may accelerate the
aging process of the bezel.
Set-Up DIP Switches
of switches is used for calibrating the meter. The values of these switches is
discussed in section 5.0 Calibrating the Meter.
selection of decimal points and backlight annunciator. Selecting “ON” position
enables the function.
While holding the unit in place, push the panel latch over the rear of the unit
The unit should be installed in a location that does not exceed the maximum
The bezel should be cleaned only with a soft cloth and neutral soap product.
Two banks of DIP switches are located inside the meter. The 9 position bank
The bank of 4 switches located near the front display are used for the
REAR TERMINALS
Main
Circuit
Board
FRONT DISPLAY
SWITCH
1
2
3
4
J
ON
4
3
2
1
1 2 3 4 5 6 7 8 9
OFFSET
UMPERS
D.P./ BACKLIGHT
OFFSET
SPAN
Backlight Annunciator for Units Label
PANEL CUT-OUT
COARSE FINE
EXCITATION
SELECT
GAIN
Decimal Point 1 (000.0)
Decimal Point 2 (00.00)
Decimal Point 3 (0.000)
FUNCTION