AD7703ARZ Analog Devices Inc, AD7703ARZ Datasheet - Page 14

• Manufacturer Part Number: AD7703ARZ
• Description: IC ADC 20BIT LC2MOS 20-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD7703ARZ

• Data Interface: Serial
• Number Of Bits: 20
• Sampling Rate (per Second): 4k
• Number Of Converters: 1
• Power Dissipation (max): 37mW
• Voltage Supply Source: Analog and Digital, Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (0.300", 7.50mm Width)
• Resolution (bits): 20bit
• Sampling Rate: 4kSPS
• Input Channel Type: Single Ended
• Supply Voltage Range - Analog: ± 4.5V To ± 5.5V
• Supply Current: 2.7mA
• Number Of Elements: 1
• Resolution: 20Bit
• Architecture: Delta-Sigma
• Sample Rate: 16KSPS
• Input Polarity: Unipolar/Bipolar
• Input Type: Voltage
• Rated Input Volt: 2.5/±2.5V
• Differential Input: No
• Power Supply Requirement: Dual
• Single Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (typ): ±5V
• Dual Supply Voltage (min): ±4.5V
• Dual Supply Voltage (max): ±5.5V
• Power Dissipation: 37mW
• Differential Linearity Error: ±0.5LSB(Typ)
• Integral Nonlinearity Error: ±0.003%FSR
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 20
• Package Type: SOIC W
• Input Signal Type: Single-Ended
• Package: 20SOIC W
• Number Of Analog Inputs: 1
• Digital Interface Type: Serial (SPI)
• Polarity Of Input Voltage: Unipolar|Bipolar
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AD7703
Synchronous Self-Clocking Mode (SSC)
The SSC mode (MODE pin high) allows easy interfacing to
serial-parallel conversion circuits in systems with parallel data
communication. This mode allows interfacing to 74XX299
Universal Shift registers without any additional decoding. The
SSC mode can also be used with microprocessors such as the
68HC11 and 68HC05, which allow an external device to clock
their serial port.
Figure 15 shows the timing diagram for the SSC mode. Data is
clocked out by an internally generated serial clock. The AD7703
divides each sampling interval into 16 distinct periods. Eight
periods of 64 clock pulses are for analog settling and eight peri-
ods of 64 clock pulses are for digital computation. The status of
CS is polled at the beginning of each digital computation period. If
it is low at any of these times, then SCLK will become active
SDATA (O)
INTERNAL
SDATA (O)
DRDY (O)
DRDY (O)
CLKIN (I)
SCLK (O)
SCLK (O)
STATUS
CS (I)
CS (I)
HI-Z
HI-Z
CYCLES
HI-Z
HI-Z
CLKIN
72 CLKIN CYCLES
72
Figure 16. SSC Mode Showing Data Timing Relative to SCLK
ANALOG TIME 0
Figure 15. Timing Diagram for SSC Transmission Mode
64 CLKIN
CYCLES
DB19 (MSB)
MSB
DIGITAL TIME 0
CS POLLED
DB18
64 CLKIN
CYCLES
–14–
DB17
and the data-word currently in the output register will be trans-
mitted, MSB first. After the LSB has been transmitted, DRDY
will go high until the new data-word becomes available. If CS,
having been brought low, is taken high again at any time during
data transmission, SDATA and SCLK will go three-state after
the current bit finishes. If CS is subsequently brought low,
transmission will resume with the next bit during the subse-
quent digital computation period. If transmission has not been
initiated and completed by the time the next data-word is avail-
able, DRDY will go high for four clock cycles then low again as
the new word is loaded into the output register.
A more detailed diagram of the data transmission in the SSC
mode is shown in Figure 16. Data bits change on the falling
edge of SCLK and are valid on the rising edge of SCLK.
LSB
1024 CLKIN CYCLES
DB2
HI-Z
HI-Z
DIGITAL TIME 7
DB1
DB0 (LSB)
HI-Z
HI-Z
REV. E