AD7243AN Analog Devices Inc, AD7243AN Datasheet - Page 6

• Manufacturer Part Number: AD7243AN
• Description: IC SRL DAC 12BIT LC2MOS 16-DIP
• Manufacturer: Analog Devices Inc
• Series: DACPORT®r

Specifications of AD7243AN

• Data Interface: Serial
• Settling Time: 10µs
• Rohs Status: RoHS non-compliant
• Number Of Bits: 12
• Number Of Converters: 1
• Voltage Supply Source: Dual ±
• Power Dissipation (max): 100mW
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 16-DIP (0.300", 7.62mm)
• Resolution (bits): 12bit
• Digital Ic Case Style: DIP
• No. Of Pins: 16
• Operating Temperature Range: -40°C To +85°C
• Update Rate: 0.1MSPS
• Package: 16PDIP
• Resolution: 12 Bit
• Conversion Rate: 300 KSPS
• Architecture: R-2R
• Digital Interface Type: Serial (3-Wire)
• Number Of Outputs Per Chip: 1
• Output Type: Voltage
• Full Scale Error: ±6 LSB
• Integral Nonlinearity Error: ±1 LSB
• Maximum Settling Time: 10 us
• Number Of Channels: 1
• Interface Type: Serial (3-Wire)
• Single Supply Voltage (typ): 12/15V
• Dual Supply Voltage (typ): ±12/±15V
• Power Supply Requirement: Single/Dual
• Single Supply Voltage (min): 10.8V
• Single Supply Voltage (max): 16.5V
• Dual Supply Voltage (min): ±10.8V
• Dual Supply Voltage (max): ±16.5V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 16
• Package Type: PDIP
• Lead Free Status / Rohs Status: Not Compliant

AD7243
0 V, to allow full sink capability of 2.5 mA over the entire
output range and to eliminate the effects of negative offsets on
the transfer characteristic (outlined previously). A plot of the
output sink capability of the amplifier is shown in Figure 5.
DIGITAL INTERFACE
The AD7243 contains an input serial to parallel shift register
and a DAC latch. A simplified diagram of the input loading
SCLK
SYNC
LDAC
SDIN
CLR
3
2
0
*
1
= DON'T CARE
0
V
DCEN
SYNC
LDAC
SCLK
SDIN
SS
CLR
= –15V
2
OUTPUT VOLTAGE – Volts
4
t
2
DB15
V
SS
= 0V
*
RESET
6
DB14
COUNTER/
DECODER
÷
*
16
AUTO – UPDATE
CIRCUITRY
8
EN
DB13
t
1
*
10
GATING
SIGNAL
DB12
*
GATED
SCLK
circuitry is shown in Figure 6. Serial data on the SDIN input is
loaded to the input register under control of DCEN, SYNC and
SCLK. When a complete word is held in the shift register, it
may then be loaded into the DAC latch under control of
LDAC. Only the data in the DAC latch determines the analog
output on the AD7243.
The DCEN (daisy-chain enable) input is used to select either a
standalone mode or a daisy-chain mode. The loading format is
slightly different depending on which mode is selected.
Serial Data Loading Format (Standalone Mode)
With DCEN at Logic 0 the standalone mode is selected. In this
mode a low SYNC input provides the frame synchronization
signal which tells the AD7243 that valid serial data on the SDIN
input will be available for the next 16 falling edges of SCLK. An
internal counter/decoder circuit provides a low gating signal so
that only 16 data bits are clocked into the input shift register.
After 16 SCLK pulses the internal gating signal goes inactive
(high) thus locking out any further clock pulses. Therefore, ei-
ther a continuous clock or a burst clock source may be used to
clock in the data.
The SYNC input should be taken high after the complete 16-bit
word is loaded in.
t
4
DB11
MSB
t
5
INPUT SHIFT REGISTER (16 BITS)
DAC LATCH (12 BITS)
DB0
LSB
t
3
t
6
t
7
SDO
t
8
t
9