EVAL-AD7934CB Analog Devices Inc, EVAL-AD7934CB Datasheet - Page 21

• Manufacturer Part Number: EVAL-AD7934CB
• Manufacturer: Analog Devices Inc

Specifications of EVAL-AD7934CB

• Lead Free Status / Rohs Status: Not Compliant

Another method of driving the AD7933/AD7934 is to use the
AD8138
single-ended-to-differential amplifier, or differential-to-differential
amplifier. The device is as easy to use as an op amp and greatly
simplifies differential signal amplification and driving.
Pseudo Differential Mode
The AD7933/AD7934 can have two pseudo differential pairs by
setting the MODE0 and MODE1 bits in the control register to 1
and 0, respectively. V
must have an amplitude of V
range chosen) to make use of the full dynamic range of the part.
A dc input is applied to the V
input provides an offset from ground or a pseudo ground for
the V
they separate the analog input signal ground from the ADC
ground, allowing the cancellation of dc common-mode
voltages. Typically, this range can extend to −0.3 V to +0.7 V
when V
shows a connection diagram for pseudo differential mode.
GND
V
GND
REF
Figure 28. Dual Op Amp Circuit to Convert a Single-Ended Unipolar
2 × V
IN
V
+ input. The benefit of pseudo differential inputs is that
REF
DD
Figure 27. Dual Op Amp Circuit to Convert a Single-Ended
REF
differential amplifier. The AD8138 can be used as a
p-p
= 3 V, or −0.3 V to +1.8 V when V
p-p
Bipolar Signal into a Unipolar Differential Signal
220Ω
440Ω
20kΩ
440Ω
A
A
Signal into a Differential Signal
220Ω
220Ω
220Ω
220Ω
220Ω
220Ω
IN
+
+ is connected to the signal source and
10kΩ
V+
V–
V+
V–
V+
V–
V+
V–
10kΩ
REF
IN−
(or 2 × V
27Ω
27Ω
27Ω
27Ω
pin. The voltage applied to this
REF
depending on the
DD
3.75V
2.5V
1.25V
3.75V
2.5V
1.25V
3.75V
2.5V
1.25V
3.75V
2.5V
1.25V
= 5 V. Figure 29
V
V
V
V
IN+
AD7933/
AD7934
IN–
IN+
IN–
AD7933/
AD7934
0.47µF
0.47µF
V
V
REF
REF
Rev. B | Page 21 of 32
ANALOG INPUT SELECTION
As shown in Table 10, users can set up their analog input
configuration by setting the values in the MODE0 and MODE1
bits in the control register. Assuming the configuration has been
chosen, there are two different ways of selecting the analog
input to be converted depending on the state of the SEQ0 and
SEQ1 bits in the control register.
Traditional Multichannel Operation (SEQ0 = SEQ1 = 0)
Any one of four analog input channels or two pairs of channels
can be selected for conversion in any order by setting the SEQ0
and SEQ1 bits in the control register to 0. The channel to be
converted is selected by writing to the address bits, ADD1 and
ADD0, in the control register to program the multiplexer prior
to the conversion. This mode of operation is that of a traditional
multichannel ADC where each data write selects the next
channel for conversion. Figure 30 shows a flowchart of this
mode of operation. The channel configurations are shown in
Table 10.
Using the Sequencer: Consecutive Sequence
(SEQ0 = 1, SEQ1 = 1)
A sequence of consecutive channels can be converted beginning
with Channel 0 and ending with a final channel selected by
writing to the ADD1 and ADD0 bits in the control register. This
is done by setting the SEQ0 and SEQ1 bits in the control
register both to 1. Once the control register is written to, the
next conversion is on Channel 0, then Channel 1, and so on
until the channel selected by the Address Bit ADD1 and Address
Bit ADD0 is reached. The ADC then returns to Channel 0 and
*ADDITIONAL PINS OMITTED FOR CLARITY.
V
REF
Figure 29. Pseudo Differential Mode Connection Diagram
Figure 30. Traditional Multichannel Operation Flow Chart
ISSUE CONVST PULSE TO INITIATE A CONVERSION
p-p
CHANGING THE VALUES OF BITS ADD2 TO ADD0
INITIATE A WRITE CYCLE TO SELECT THE NEXT
IN THE CONTROL REGISTER. SEQ0 = SEQ1 = 0.
CHANNEL TO CONVERT ON (ADD1 TO ADD0).
INITIATE A READ CYCLE TO READ THE DATA
SET SEQ0 = SEQ1 = 0. SELECT THE DESIRED
SET UP OPERATING MODE, ANALOG INPUT
WRITE TO THE CONTROL REGISTER TO
CHANNEL TO BE CONVERTED ON BY
FROM THE SELECTED CHANNEL.
AND OUTPUT CONFIGURATION
ON THE SELECTED CHANNEL.
POWER ON
VOLTAGE
DC INPUT
AD7933/AD7934
V
V
V
REF
IN+
IN–
+
AD7933/
AD7934*
0.47µF